Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  Power Slide Door ECU LH Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the slide control relay LH (ECU).

WIRING DIAGRAM

B138842E01
3.974,2.087 5.797,2.428 1.823,0.341 10 Door Control Relay LH (Power Slide Door ECU LH) 2.815,0.156 3.299,0.331 0.485,0.174 10 ECU-B 4.388,0.299 4.854,0.473 0.466,0.174 10 ECUB 4.388,1.532 4.771,1.706 0.383,0.174 10 GND 3.974,1.919 4.357,2.093 0.383,0.174 10 M22 4.388,0.71 4.577,0.884 0.188,0.174 10 B 4.388,1.121 4.604,1.295 0.216,0.174 10 IG 2.779,0.554 3.375,0.728 0.596,0.174 10 PSD LH 2.68,0.974 3.461,1.149 0.781,0.174 10 LH ECU-IG 0.915,1.109 1.876,1.284 0.961,0.174 10 from Battery 0.915,0.712 1.876,0.886 0.961,0.174 10 from Battery 0.915,0.31 1.876,0.485 0.961,0.174 10 from Battery 4.004,1.395 4.246,1.569 0.242,0.174 10 1 4.004,1.003 4.246,1.177 0.242,0.174 10 4 4.004,0.582 4.246,0.757 0.242,0.174 10 7 4.004,0.148 4.246,0.322 0.242,0.174 10 12

PROCEDURE

1.INSPECT FUSE (ECU-B, PSD LH, LH ECU-IG)
a.

Remove the PSD LH and LH ECU-IG fuses from instrument panel junction block.


b.

Remove the ECU-B fuse from engine room No. 1 relay block and junction block.


c.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω




OK

2.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)
a.
U185970E03
1.208,1.208 0.667,1.396 true 1.813,1.271 2.219,0.667 2.219,0.667 2.313,0.667 true 2.188,1.531 2.542,1.76 true 1.219,1.5 0.979,1.823 true 0.042,0.042 1.375,0.24 1.333,0.198 10 false Wire Harness Side: 0.313,0.771 0.635,0.948 0.323,0.177 10 false M22 0.323,1.333 0.719,1.563 0.396,0.229 10 false GND 0.865,1.833 1.333,2.031 0.469,0.198 10 false B 2.375,0.604 2.74,0.75 0.365,0.146 10 false IG 2.594,1.698 3.073,1.906 0.479,0.208 10 false ECUB

Disconnect the M22 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
M22-12 (ECUB) - Body ground 10 to 14 V
M22-4 (IG) - Body ground 10 to 14 V
M22-7 (B) - Body ground 10 to 14 V



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
M22-1 (GND) - Body ground Below 1 Ω




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR