Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  Power Slide Door ECU RH Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the slide control relay RH (ECU).

WIRING DIAGRAM

B138842E21
3.979,2.073 5.802,2.417 1.823,0.344 10 false Door Control Relay RH (Power Slide Door ECU RH) 2.813,0.156 3.302,0.333 0.49,0.177 10 false ECU-B 4.385,0.302 4.854,0.479 0.469,0.177 10 false ECUB 4.385,1.531 4.771,1.708 0.385,0.177 10 false GND 3.979,1.896 4.365,2.073 0.385,0.177 10 false N24 4.385,0.708 4.573,0.885 0.188,0.177 10 false B 4.385,1.125 4.604,1.302 0.219,0.177 10 false IG 2.781,0.552 3.375,0.729 0.594,0.177 10 false PSD RH 2.677,0.979 3.458,1.156 0.781,0.177 10 false RH ECU-IG 1.042,1.125 1.906,1.365 0.865,0.24 10 false from Battery 1.042,0.708 1.906,0.948 0.865,0.24 10 false from Battery 1.042,0.313 1.906,0.552 0.865,0.24 10 false from Battery 4.073,0.604 4.302,0.781 0.229,0.177 10 false 12 4.135,0.198 4.365,0.375 0.229,0.177 10 false 7 4.115,1.396 4.344,1.573 0.229,0.177 10 false 6 4.115,1.021 4.344,1.198 0.229,0.177 10 false 3

PROCEDURE

1.INSPECT FUSE (ECU-B, PSD RH, RH ECU-IG)
a.

Remove the PSD RH and RH ECU-IG fuses from instrument panel junction block (passenger side).


b.

Remove the ECU-B fuses from engine room No. 1 relay block and junction block.


c.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω




OK

2.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)
a.
U185971E03
2.188,1.177 2.531,1.073 false 1.625,1.26 1.542,0.646 1.542,0.646 1.427,0.646 false 1.219,1.448 0.875,1.51 false 2.135,1.521 2.188,1.906 false 0.042,0.052 1.375,0.25 1.333,0.198 10 false Wire Harness Side: 0.313,0.781 0.635,0.958 0.323,0.177 10 false N24 2.573,0.979 2.969,1.208 0.396,0.229 10 false GND 2.156,1.927 2.625,2.125 0.469,0.198 10 false B 1.26,0.594 1.625,0.74 0.365,0.146 10 false IG 0.448,1.448 0.927,1.656 0.479,0.208 10 false ECUB

Disconnect the N24 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
N24-7 (ECUB) - Body ground 10 to 14 V
N24-3 (IG) - Body ground 10 to 14 V
N24-12 (B) - Body ground 10 to 14 V



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
N24-6 (GND) - Body ground Below 1 Ω




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR