Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  Power Slide Door Sensor RH Circuit  


DESCRIPTION

When the power slide door sensor (touch sensor) sends a jam detection signal to the door control relay (power slide door ECU), the ECU stops the close operation of the power slide door.

WIRING DIAGRAM

B138843E02
1.115,2.055 2.947,2.378 1.832,0.323 10 Power Slide Door Sensor RH (Touch Sensor RH) 4.45,1.987 6.226,2.351 1.776,0.363 10 Door Control Relay RH (Power Slide Door ECU RH) 4.973,0.724 5.203,0.899 0.230,0.174 10 OS 2.965,0.556 3.195,0.731 0.230,0.174 10 OS 4.973,1.443 5.342,1.618 0.369,0.174 10 OSG 4.45,1.826 4.694,2.001 0.244,0.174 10 K6 4.716,0.62 4.865,0.794 0.149,0.174 10 6 4.716,1.344 4.865,1.518 0.149,0.174 10 2 3.336,0.62 3.485,0.794 0.149,0.174 10 1 3.336,1.344 3.485,1.518 0.149,0.174 10 2 1.115,1.878 1.359,2.052 0.244,0.174 10 K7 2.853,1.537 3.222,1.711 0.369,0.174 10 OSG

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Use the Data List to check if the touch sensor is functioning properly.

Door control relay RH (Power slide door ECU RH)
Item Measurement Item / Display (Range) Normal Condition Diagnosis Note
PSD Touch Sensor Power slide door touch sensor signal / OFF, ON or OPEN OFF: Power slide door touch sensor is not pressed
ON: Power slide door touch sensor is pressed
OPEN: Power slide door touch sensor is opened
-

OK:

When the touch sensor is operating, the intelligent tester should display as shown in the table.




NG

2.INSPECT POWER SLIDE DOOR TOUCH SENSOR RH

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT POWER SLIDE DOOR TOUCH SENSOR RH
a.
B138847E02
2.277,1.66 2.821,1.844 0.545,0.184 10 Pressed 0.48,1.66 0.835,1.844 0.355,0.184 10 Free

Remove the power slide door touch sensor.


b.

Measure the resistance of the touch sensor.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 Pressed Below 100 Ω
1 - 2 Free Approximately 1 kΩ




OK

3.CHECK WIRE HARNESS (SENSOR - ECU AND BODY GROUND)

NG

REPLACE POWER SLIDE DOOR SENSOR RH

3.CHECK WIRE HARNESS (SENSOR - ECU AND BODY GROUND)
a.
U188692E02
1.875,1.906 2.25,2.188 false 1.49,3.667 1.115,3.948 false 1.531,1.906 1.042,2.167 false 1.583,3.854 1.906,4.385 false 0.156,0.135 1.479,0.292 1.323,0.156 10 false Wire Harness Side: 1.156,0.771 2.313,0.917 1.156,0.146 10 false Touch Sensor RH 0.896,2.719 2.594,2.896 1.698,0.177 10 false Power Slide Door ECU RH 0.698,1.406 0.917,1.552 0.219,0.146 10 false K7 0.698,3.396 0.917,3.542 0.219,0.146 10 false K6 1.948,4.406 2.198,4.552 0.25,0.146 10 false OS 2.271,2.146 2.521,2.292 0.25,0.146 10 false OS 0.813,3.896 1.219,4.042 0.406,0.146 10 false OSG 0.698,2.104 1.104,2.25 0.406,0.146 10 false OSG

Disconnect the K7 sensor connector.


b.

Disconnect the K6 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
K7-1 (OS) - K6-6 (OS) Below 1 Ω
K7-2 (OSG) - K6-2 (OSG) Below 1 Ω
K7-1 (OS) - Body ground 10 kΩ or higher
K7-2 (OSG) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR