Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  Slide Door Handle Switch LH Circuit  


DESCRIPTION

The inside / outside handles have the ability to control operation of the power slide door. Pulling either handle transmits a request signal to the power slide door ECU LH, which then commands the power slide door control motor and clutch to open / close the power slide door.

WIRING DIAGRAM

B138841E01
1.697,1.858 3.964,2.209 2.267,0.350 10 Slide Door Lock Remote Control LH (Slide Door Handle Switch LH) 4.898,2.017 6.648,2.403 1.750,0.386 10 Door Control Relay LH (Power Slide Door ECU LH) 1.969,1.426 2.332,1.634 0.363,0.208 10 GND 3.295,0.532 3.619,0.710 0.324,0.178 10 DS1 3.295,1.138 3.619,1.315 0.324,0.178 10 DS2 5.287,0.656 5.611,0.833 0.324,0.178 10 DS1 5.287,1.262 5.611,1.439 0.324,0.178 10 DS2 4.898,1.857 5.222,2.035 0.324,0.178 10 L6 5.003,0.554 5.237,0.732 0.233,0.178 10 10 5.043,1.15 5.276,1.327 0.233,0.178 10 7 3.709,0.554 3.943,0.732 0.233,0.178 10 1 3.709,1.15 3.942,1.327 0.233,0.178 10 2 1.763,1.15 1.997,1.327 0.233,0.178 10 3 1.697,1.68 2.020,1.857 0.324,0.178 10 L9

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (HANDLE SWITCH)
a.

Use the Data List to check if the door lock is functioning properly.

Door control relay LH (Power slide door ECU LH)
Item Measurement Item / Display (Range) Normal Condition Diagnosis Note
Handle SW1 Handle operation detect switch signal / ON or OFF ON: Slide door inside / outside handle is pulled
OFF: Slide door inside / outside handle is not pulled
-
Handle SW2 Handle operation detect switch signal / ON or OFF ON: Slide door inside / outside handle is pulled
OFF: Slide door inside / outside handle is not pulled
-

OK:

When the handle switch is operating, the intelligent tester should display as shown in the table.




NG

2.INSPECT SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH (SLIDE DOOR HANDLE SWITCH LH)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH (SLIDE DOOR HANDLE SWITCH LH)
a.
B142338E01
2.2,0.545 2.543,0.736 0.343,0.191 10 DS1 0.588,0.541 0.931,0.731 0.343,0.191 10 DS2 2.14,1.868 2.504,2.031 0.364,0.163 10 GND 1.418,1.138 0.969,0.669 false 1.697,1.144 2.165,0.664 false 1.706,1.477 2.105,1.877 false

Remove the slide door handle switch.


b.

Measure the resistance of the slide door handle switch.

Standard resistance:
Tester Connection Condition Specified Condition
1 (DS1) - 3 (GND) Pulled handle Below 1 Ω
1 (DS1) - 3 (GND) Not pulled handle 10 kΩ or higher
2 (DS2) - 3 (GND) Pulled handle Below 1 Ω
2 (DS2) - 3 (GND) Not pulled handle 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)

NG

REPLACE SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH

3.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)
a.
U188686E02
1.708,3.719 2.427,3.479 false 2.313,1.844 1.885,1.667 false 1.188,1.844 1.583,1.656 false 1.521,3.927 1.24,4.24 false 1.135,2.115 1.563,1.938 false 0.156,0.146 1.469,0.313 1.313,0.167 10 false Wire Harness Side: 0.813,0.604 2.667,0.781 1.854,0.177 10 false Slide Door Handle Switch LH 0.896,2.594 2.583,2.771 1.688,0.177 10 false Power Slide Door ECU LH 0.875,1.208 1.073,1.365 0.198,0.156 10 false L9 0.708,3.323 0.906,3.479 0.198,0.156 10 false L6 0.99,4.271 1.323,4.427 0.333,0.156 10 false DS1 0.875,1.792 1.208,1.948 0.333,0.156 10 false DS1 2.479,3.396 2.813,3.552 0.333,0.156 10 false DS2 2.354,1.844 2.688,2 0.333,0.156 10 false DS2 0.771,2.073 1.104,2.229 0.333,0.156 10 false GND

Disconnect the L9 switch connector.


b.

Disconnect the L6 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
L9-1 (DS1) - L6-10 (DS1) 10 kΩ or higher
L9-2 (DS2) - L6-7 (DS2) 10 kΩ or higher
L9-3 (GND) - Body ground Below 1 Ω
L9-1 (DS1) - Body ground Below 1 Ω
L9-2 (DS2) - Body ground Below 1 Ω




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR