Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292019 POWER SLIDE DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER SLIDE DOOR SYSTEM  Slide Door Lock Release Motor LH Circuit  


DESCRIPTION

The slide door lock release motor unlocks the power slide door lock and unlock position switch when the power slide door is operated by the transmitter or power slide door control switch with the slide door closed.

WIRING DIAGRAM

B138815E02
1.67,1.527 3.889,1.683 2.218,0.156 10 Slide Door Lock Release Motor LH 2.92,0.831 3.249,0.990 0.328,0.159 10 SD+ 2.236,0.831 2.559,0.990 0.323,0.159 10 SD- 4.94,0.938 5.364,1.107 0.424,0.168 10 RACT 4.512,1.821 4.936,1.989 0.424,0.168 10 L6 1.67,1.37 1.920,1.539 0.250,0.168 10 L8 4.648,0.852 4.870,1.021 0.222,0.168 10 13 1.998,0.852 2.146,1.021 0.148,0.168 10 1 3.296,0.852 3.458,1.021 0.162,0.168 10 2 4.512,1.979 6.266,2.314 1.754,0.335 10 Door Control Relay LH (Power Slide Door ECU LH)

PROCEDURE

1.INSPECT SLIDE DOOR LOCK RELEASE MOTOR LH
a.
B138849E01
0.054,2.345 1.119,2.501 1.065,0.156 10 26.0 to 30.3 mm

Remove the slide door lock release motor.


b.

Apply the battery voltage to the motor terminals and check the operation of the door lock release motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (SD+)
Battery negative (-) → 1 (SD-)
Lock release


Standard stroke:

26.0 to 30.3 mm (1.02 to 1.19 in.)




OK

2.CHECK WIRE HARNESS (RELEASE MOTOR - ECU AND BODY GROUND)

NG

REPLACE SLIDE DOOR LOCK RELEASE MOTOR LH

2.CHECK WIRE HARNESS (RELEASE MOTOR - ECU AND BODY GROUND)
a.
U188688E02
1.406,3.583 1.219,4.135 false 1.135,2.083 1.563,1.875 false 2.448,1.635 1.896,1.802 false 0.135,0.125 1.521,0.292 1.385,0.167 10 false Wire Harness Side: 0.667,0.802 2.823,0.958 2.156,0.156 10 false Slide Door Lock Release Motor LH 0.969,2.635 2.417,2.792 1.448,0.156 10 false Door Control Relay LH 0.688,1.458 0.875,1.646 0.188,0.188 10 false L8 0.583,3.229 0.875,3.417 0.292,0.188 10 false L6 2.5,1.563 2.823,1.719 0.323,0.156 10 false SD- 1.021,4.177 1.417,4.333 0.396,0.156 10 false RACT 0.844,2.094 1.167,2.25 0.323,0.156 10 false SD+

Disconnect the L8 slide door lock release motor connector.


b.

Disconnect the L6 body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
L8-2 (SD+) - L6-13 (RACT) Below 1 Ω
L8-1 (SD-) - Body ground Below 1 Ω
L8-2 (SD+) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR