Home › Vehicle Interior › ENGINE HOOD / DOOR › SLIDE DOOR CLOSER SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292020 SLIDE DOOR CLOSER SYSTEM J

ENGINE HOOD / DOOR  SLIDE DOOR CLOSER SYSTEM  Slide Door Closer Motor RH Circuit  


DESCRIPTION

The power slide door ECU*1 or slide door closer relay*2 controls the slide door lock motor. This ECU*1 or relay*2 applies current to terminals DC+ and DC- to operate the motor to close the door. It reverses the direction of the current to operate the motor to open the door.

*1: w/ Power Slide Door RH

*2: w/o Power Slide Door RH


WIRING DIAGRAM

B220777E04
1.889,1.304 3.777,1.627 1.887,0.323 10 Slide Door Lock Assembly RH (Slide Door Closer Motor RH) 1.889,1.131 2.128,1.278 0.239,0.147 10 K5 2.907,1.024 3.304,1.208 0.397,0.184 10 ACT+ 2.328,1.024 2.725,1.208 0.397,0.184 10 ACT- 3.407,0.688 3.535,0.834 0.128,0.147 10 4 4.266,0.688 4.885,0.834 0.619,0.147 10 13*1, 2*2 4.37,1.813 4.886,1.960 0.516,0.147 10 5*1, 1*2 2.123,0.688 2.251,0.834 0.128,0.147 10 1 5.044,0.732 5.496,0.879 0.452,0.147 10 DC+*1 5.044,0.883 5.569,1.029 0.525,0.147 10 ACT+*2 5.044,2.004 5.569,2.150 0.525,0.147 10 ACT-*2 5.044,1.858 5.448,2.004 0.404,0.147 10 DC-*1 4.542,2.346 6.466,2.677 1.924,0.332 10 Door Control Relay RH (Power Slide Door ECU RH) 4.542,3.2 6.286,3.351 1.744,0.151 10 Slide Door Closer Relay RH 4.542,2.199 4.898,2.345 0.356,0.147 10 K6*1 4.542,3.048 4.984,3.195 0.442,0.147 10 K12*2 1.109,2.467 2.839,2.623 1.730,0.156 10 *1: w/ Power Slide Door RH 1.109,2.845 2.913,3.001 1.804,0.156 10 *2: w/o Power Slide Door RH

PROCEDURE

1.INSPECT SLIDE DOOR LOCK ASSEMBLY RH
a.
B137557E04
2.063,0.323 3.177,0.646 1.115,0.323 10 false Normal Rotation (Close) 0.625,2.552 1.792,2.979 1.167,0.427 10 false Reverse Rotation (Return)

Remove the slide door lock assembly RH.


b.

Apply battery voltage to the motor terminals and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition
Battery positive (+) → 4 (ACT+)
Battery negative (-) → 1 (ACT-)
Close operation
Battery positive (+) → 1 (ACT-)
Battery negative (-) → 4 (ACT+)
Return operation




OK

2.CHECK WIRE HARNESS (CLOSER MOTOR - ECU AND BODY GROUND)

NG

REPLACE SLIDE DOOR LOCK ASSEMBLY RH

2.CHECK WIRE HARNESS (CLOSER MOTOR - ECU AND BODY GROUND)
a.

Disconnect K5 closer motor connector.

U188889E01
0.073,0.052 1.372,0.232 1.299,0.179 10 Wire Harness Side: 0.558,0.459 2.214,0.791 1.656,0.332 10 Slide Door Lock RH (Slide Door Closer Motor RH) 2.753,0.459 4.520,0.615 1.767,0.156 10 Slide Door Closer Relay RH 5.023,0.367 6.790,0.705 1.767,0.338 10 Door Control Relay RH (Power Slide Door ECU RH) 0.535,1.654 0.746,1.801 0.211,0.147 10 K5 2.498,1.631 2.782,1.778 0.283,0.147 10 K12 4.976,1.626 5.188,1.773 0.211,0.147 10 K6 0.528,2.308 0.913,2.457 0.385,0.149 10 ACT- 2.854,2.14 3.211,2.289 0.357,0.149 10 ACT- 6.508,2.238 6.803,2.387 0.295,0.149 10 DC- 3.589,2.14 3.995,2.289 0.406,0.149 10 ACT+ 5.789,2.238 6.125,2.387 0.336,0.149 10 DC+ 1.817,2.308 2.202,2.457 0.385,0.149 10 ACT+ 1.022,1.696 0.703,2.308 false 1.64,1.688 1.999,2.308 false 3.25,1.682 3.029,2.14 false 3.434,1.682 3.764,2.14 false 6.143,1.9 5.938,2.214 false 6.18,1.646 6.592,2.196 false 2.851,1.622 3.044,1.787 0.193,0.165 10 *2 5.247,1.622 5.440,1.787 0.193,0.165 10 *1 2.417,2.453 4.165,2.595 1.748,0.142 10 *1: w/ Power Slide Door RH 4.388,2.453 6.201,2.595 1.813,0.142 10 *2: w/o Power Slide Door RH


b.

Disconnect K6*1 or K12*2 connector.

*1: w/ Power Slide Door RH

*2: w/o Power Slide Door RH



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
K5-1 (ACT-) - K6-5 (DC-)*1 Below 1Ω
K5-4 (ACT+) - K6-13 (DC+)*1 Below 1Ω
K5-1 (ACT-) - K12-1 (ACT-)*2 Below 1Ω
K5-4 (ACT+) - K12-2 (ACT+)*2 Below 1Ω
K5-1 (ACT-) - Body ground 10 kΩ or higher
K5-4 (ACT+) - Body ground 10 kΩ or higher


*1: w/ Power Slide Door RH

*2: w/o Power Slide Door RH




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR