Home › Vehicle Interior › ENGINE HOOD / DOOR › SLIDE DOOR CLOSER SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292020 SLIDE DOOR CLOSER SYSTEM J

ENGINE HOOD / DOOR  SLIDE DOOR CLOSER SYSTEM  Slide Door Closer Relay Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the slide door closer relay.

WIRING DIAGRAM

B222199E02
4.35,2.123 5.886,2.261 1.536,0.137 10 Slide Door Closer Relay 4.35,1.965 5.228,2.139 0.878,0.174 10 L12*1, K12*2 3.015,0.648 3.680,0.794 0.665,0.147 10 PSD LH*1 3.015,0.834 3.689,0.981 0.674,0.147 10 PSD RH*2 4.635,0.489 4.847,0.649 0.211,0.161 10 +B 4.635,1.175 4.763,1.336 0.128,0.161 10 E 1.338,0.47 2.128,0.640 0.790,0.170 10 from Battery 0.413,1.586 1.328,1.742 0.915,0.156 10 *1: for LH side 0.413,1.979 1.370,2.134 0.957,0.156 10 *2: for RH side 4.411,0.381 4.521,0.542 0.110,0.161 10 5 4.411,1.068 4.521,1.228 0.110,0.161 10 8

PROCEDURE

1.INSPECT FUSE (PSD LH*1 OR PSDRH*2)
a.

Remove the PSD LH*1 or PSD RH*2 fuse from the instrument panel junction block.

*1: for LH side

*2: for RH side



b.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω




OK

2.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK WIRE HARNESS (ECU AND BATTERY AND BODY GROUND)
a.
U188664E01
0.014,0.017 1.314,0.159 1.299,0.142 10 Wire Harness Side: 0.805,0.338 2.331,0.480 1.526,0.142 10 Slide Door Closer Relay 0.322,0.974 0.587,1.119 0.265,0.145 10 L12 0.322,1.275 0.592,1.420 0.270,0.145 10 K12 0.728,0.982 0.887,1.128 0.159,0.145 10 *1 0.728,1.257 0.887,1.403 0.159,0.145 10 *2 0.363,1.822 1.271,1.960 0.908,0.139 10 *1: for LH side 1.649,1.835 2.581,1.973 0.932,0.139 10 *2: for RH side 0.762,1.606 0.973,1.751 0.211,0.145 10 +B 2.481,1.606 2.595,1.751 0.114,0.145 10 E 1.233,1.36 0.895,1.606 false 1.875,1.365 2.481,1.679 false

Disconnect the L12*1 or K12*2 relay connector.


*1: for LH side

*2: for RH side


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
L12-5 (+B) - Body ground*1 10 to 14 V
K12-5 (+B) - Body ground*2 10 to 14 V


*1: for LH side

*2: for RH side



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
L12-8 (E) - Body ground*1 Below 1 Ω
K12-8 (E) - Body ground*2 Below 1 Ω


*1: for LH side

*2: for RH side




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR