Home › Vehicle Interior › ENGINE HOOD / DOOR › SLIDE DOOR CLOSER SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292020 SLIDE DOOR CLOSER SYSTEM J

ENGINE HOOD / DOOR  SLIDE DOOR CLOSER SYSTEM  Slide Door Handle Switch LH Circuit  


DESCRIPTION

Pulling either the inside or outside handle transmits a request signal to the slide door closer relay, which then commands the slide door closer motor to close the slide door.

WIRING DIAGRAM

B222196E05
1.847,2.598 2.756,2.737 0.909,0.140 10 Handle Switch 1.651,1.001 2.979,1.140 1.328,0.140 10 Initial Position Switch 3.22,2.36 3.334,2.499 0.114,0.139 10 3 3.22,0.757 3.334,0.896 0.114,0.139 10 7 4.572,0.757 4.686,0.896 0.114,0.139 10 7 4.493,2.368 4.686,2.507 0.193,0.139 10 10 1.299,2.36 1.413,2.499 0.114,0.139 10 2 1.229,0.744 1.412,0.883 0.183,0.139 10 10 4.78,2.444 5.126,2.608 0.346,0.164 10 LSW 4.78,0.87 5.126,1.034 0.346,0.164 10 GND 1.511,0.744 1.843,0.909 0.332,0.165 10 HND 2.684,0.744 3.103,0.909 0.419,0.165 10 GND2 1.511,2.358 1.843,2.523 0.332,0.165 10 DS1 2.761,2.358 3.104,2.523 0.342,0.165 10 GND 1.329,1.556 3.193,1.694 1.864,0.137 10 Slide Door Lock Assembly LH 0.941,3.069 3.833,3.373 2.892,0.304 10 Slide Door Lock Remote Control Assembly LH (Slide Door Handle Switch LH) 1.329,1.411 1.515,1.558 0.186,0.147 10 L5 0.965,2.915 1.151,3.062 0.186,0.147 10 L9 4.336,3.205 6.066,3.361 1.730,0.156 10 Slide Door Closer Relay LH 4.346,3.046 4.622,3.210 0.276,0.164 10 L12

PROCEDURE

1.INSPECT SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH (SLIDE DOOR HANDLE SWITCH LH)
a.
B142338E06
0.619,1.825 0.962,2.016 0.343,0.191 10 DS1 2.14,1.825 2.504,1.988 0.364,0.163 10 GND 0.782,1.825 1.409,1.238 false 1.706,1.443 2.105,1.843 false

Remove the slide door lock remote control assembly LH.


b.

Measure the resistance of the slide door handle switch.

Standard resistance:
Tester Connection Condition Specified Condition
2 (DS1) - 3 (GND) Handle pulled Below 1 Ω
2 (DS1) - 3 (GND) Handle not pulled 10 kΩ or higher




OK

2.INSPECT SLIDE DOOR LOCK ASSEMBLY LH

NG

REPLACE SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH

2.INSPECT SLIDE DOOR LOCK ASSEMBLY LH
a.
B140911E04
1.115,1.469 1.417,0.521 1.417,0.521 1.229,0.521 false 1.677,2.521 1.677,2.917 false 0.219,0.417 1.073,0.573 0.854,0.156 10 false Active Lever 1.344,2.938 2.156,3.094 0.813,0.156 10 false Initial Switch

Remove the slide door lock assembly LH.


b.

Measure the resistance of the slide door lock assembly.

Standard resistance:
Tester Connection Condition Specified Condition
10 - 7 Initial position 10 kΩ or higher
10 - 7 Except initial position (slide door closer operating) Below 1 Ω




OK

3.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)

NG

REPLACE SLIDE DOOR LOCK ASSEMBLY LH

3.CHECK WIRE HARNESS (SWITCH - ECU AND BODY GROUND)
a.

Disconnect the L9 and L5 connectors.

U188893E01
0.087,0.006 1.391,0.152 1.304,0.147 10 Wire Harness Side: 0.589,0.629 2.325,0.769 1.737,0.140 10 Slide Door Closer Relay LH 2.842,0.103 4.593,0.579 1.751,0.476 10 Slide Door Lock Remote Control Assembly LH (Slide Door Handle Switch LH) 4.965,0.642 6.847,0.799 1.883,0.157 10 Slide Door Lock Assembly LH 0.498,1.603 0.775,1.773 0.277,0.170 10 L12 2.921,1.68 3.112,1.850 0.191,0.170 10 L9 5.044,1.75 5.235,1.920 0.191,0.170 10 L5 0.904,2.205 1.254,2.389 0.350,0.184 10 GND 5.177,2.205 5.627,2.389 0.450,0.184 10 GND2 6.396,2.205 6.746,2.389 0.350,0.184 10 HND 1.976,2.205 2.326,2.389 0.350,0.184 10 LSW 6.211,1.958 6.536,2.205 false 5.823,1.968 5.389,2.205 false 1.843,1.831 2.144,2.205 false 1.361,1.825 1.044,2.205 false 2.98,2.124 3.330,2.307 0.350,0.184 10 GND 4.159,2.124 4.470,2.307 0.311,0.184 10 DS1 3.575,1.954 3.318,2.205 false 3.871,1.709 4.262,2.124 false


b.

Disconnect the L12 relay connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
L12-10 (LSW) - L9-3 (GND) Below 1 Ω
L9-2 (DS1) - L5-10 (HND) Below 1 Ω
L12-7 (GND) - L5-7 (GND2) Below 1 Ω
L12-10 (LSW) - Body ground 10 kΩ or higher
L9-2 (DS1)- Body ground 10 kΩ or higher
L12-7 (GND) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR