Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER BACK DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292031 POWER BACK DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER BACK DOOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to operate the power back door ECU.

WIRING DIAGRAM

B138232E05
6.125,1.396 6.563,1.552 0.438,0.156 10 false ECUB 6.135,2.01 6.344,2.156 0.208,0.146 10 false B 6.146,2.729 6.406,2.896 0.26,0.167 10 false IG 6.146,3.375 6.5,3.542 0.354,0.167 10 false GND 4.146,2.615 4.896,2.781 0.75,0.167 10 false LH ECU-IG 4.365,1.885 4.708,2.052 0.344,0.167 10 false PBD 4.281,1.292 4.75,1.438 0.469,0.146 10 false ECU-B 2.979,2.385 3.417,2.552 0.438,0.167 10 false LH-IG 1.365,1.406 2.167,1.583 0.802,0.177 10 false from Battery 1.365,1.99 2.167,2.167 0.802,0.177 10 false from Battery 1.365,2.719 2.167,2.896 0.802,0.177 10 false from Battery 0.802,3.365 2.167,3.573 1.365,0.208 10 false from Main Body ECU 5.521,3.885 5.813,4.031 0.292,0.146 10 false M24 5.875,3.49 6.052,3.635 0.177,0.146 10 false 11 5.938,2.844 6.115,3.052 0.177,0.208 10 false 8 5.875,2.094 6.073,2.24 0.198,0.146 10 false 12 5.875,1.531 6.073,1.677 0.198,0.146 10 false 10 5.51,4.052 7.125,4.375 1.615,0.323 10 false Power Back Door Unit (Power Back Door ECU)

PROCEDURE

1.INSPECT FUSE (LH ECU-IG , ECU-B, PDR)
a.

Remove the LH ECU-IG, ECU-B fuses from the main body ECU.


b.

Remove the ECU-B fuse from the engine room No. 1 junction block.


c.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω




OK

2.CHECK WIRE HARNESS (POWER BACK DOOR UNIT - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK WIRE HARNESS (POWER BACK DOOR UNIT - BATTERY AND BODY GROUND)
U188591E02
0.031,0 1.480,0.154 1.449,0.154 10 Wire Harness Side: 1.581,0.42 1.936,0.566 0.356,0.145 10 M24 2.466,1.143 2.737,1.641 false 2.255,1.116 2.154,1.692 false 2.704,1.117 3.158,1.572 false 1.923,1.177 1.701,1.675 false 1.6,1.687 1.850,1.837 0.250,0.149 10 IG 2.522,1.698 2.908,1.859 0.385,0.161 10 GND 3.111,1.573 3.316,1.729 0.205,0.156 10 B 1.883,1.692 2.332,1.876 0.449,0.184 10 ECUB

a.

Disconnect the M24 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Switch Condition Specified Condition
M24-8 (IG) - Body ground Engine switch on (IG) 10 to 14 V
M24-8 (IG) - Body ground Engine switch off Below 1 V
M24-10 (ECUB) - Body ground Always 10 to 14 V
M24-8 (B) - Body ground Always 10 to 14 V



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
M24-11 (GND) - Body ground Below 1 Ω




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR