Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER BACK DOOR SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292031 POWER BACK DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER BACK DOOR SYSTEM  Back Door Lock Latch Switch Circuit  


DESCRIPTION

The full latch switch and half-latch switch are built into the back door lock. The full latch switch detects when the latch is not completely engaged. This switch turns on when the back door is open or the latch is not completely engaged. The half-latch switch detects when the latch is completely engaged. This switch turns on when the latch is in the over-latch position.

WIRING DIAGRAM

B144429E03
5.708,0.813 6.021,0.958 0.313,0.146 10 false HAF 5.708,2.01 6.021,2.198 0.313,0.188 10 false POS 1.177,2.25 2.156,2.438 0.979,0.188 10 false Selector Switch 1.198,1.156 2.292,1.302 1.094,0.146 10 false Full-latch Switch 1.063,2.885 2.083,3.063 1.021,0.177 10 false Back Door Lock 1.802,0.677 2.271,0.844 0.469,0.167 10 false ULSW 1.865,1.875 2.292,2.042 0.427,0.167 10 false DLSW 5.5,2.583 5.833,2.75 0.333,0.167 10 false M24 5.438,2.104 5.646,2.26 0.208,0.156 10 false 24 5.427,0.917 5.635,1.063 0.208,0.146 10 false 22 2.354,0.906 2.542,1.083 0.188,0.177 10 false 5 2.354,2.115 2.552,2.313 0.198,0.198 10 false 6 0.688,2.125 0.865,2.333 0.177,0.208 10 false E 0.448,2.125 0.594,2.292 0.146,0.167 10 false 4 1.063,2.75 1.344,2.896 0.281,0.146 10 false S12 5.5,2.719 7.052,3.063 1.552,0.344 10 false Power Back Door Unit (Power Back Door ECU)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FULL-LATCH AND SELECTOR SWITCH)
a.

Check the Data List for proper functioning of the full-latch switch and selector switch.

Power back door unit (Power back door ECU)
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Half Latch SW Half-latch switch signal / ON or OFF ON: Back door lock motor is open latch or over-latch
OFF: Back door lock motor is full-latch or half-latch
-
Closer Pos Closer position switch signal ON: Back door lock center gear is center position
OFF: Back door lock center gear is except center position
-

OK:

The display is as specified in the normal condition.




NG

2.INSPECT BACK DOOR LOCK (FULL-LATCH SWITCH AND SELECTOR SWITCH)

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT BACK DOOR LOCK (FULL-LATCH SWITCH AND SELECTOR SWITCH)
B143899E24
3.083,2.51 3.75,3.583 3.75,3.583 3.802,3.583 true 4.958,2.646 5.188,2.125 false 5.365,2.104 5.531,2.667 false 4.656,2.25 5.188,1.938 false 4.479,3.927 5.177,4.083 0.698,0.156 10 false Over-latch 4.385,4.281 5,4.427 0.615,0.146 10 false Full-latch 4.115,5.26 4.729,5.406 0.615,0.146 10 false Half-latch 3.677,5.865 4.406,6.042 0.729,0.177 10 false Open-latch 3.198,1.771 3.625,2.021 0.427,0.25 10 true Close 2.198,1.729 2.719,2.01 0.521,0.281 10 true Release 3.823,3.531 4.531,3.688 0.708,0.156 10 false Drive Gear 5.344,2.667 5.781,2.885 0.438,0.219 10 false ULSW 4.542,2.188 4.677,2.344 0.135,0.156 10 false E 4.75,2.667 5.167,2.885 0.417,0.219 10 false DLSW

a.

Remove the back door lock (see page Vehicle Interior>ENGINE HOOD / DOOR>BACK DOOR>DISASSEMBLY).


b.

Measure the resistance of the switch.

Standard resistance:
Full-latch switch
Tester Connection Door Lock Latch Position Specified Condition
5 (ULSW) - 4 (E) Over-latch Below 1 Ω
5 (ULSW) - 4 (E) Open-latch 10 kΩ or higher
5 (ULSW) - 4 (E) Full-latch 10 kΩ or higher
5 (ULSW) - 4 (E) Half-latch 10 kΩ or higher


Selector switch:
Tester Connection Door Lock Latch Position Specified Condition
6 (DLSW) - 4 (E) Open-latch Below 1 Ω
6 (DLSW) - 4 (E) Over-latch 10 kΩ or higher
6 (DLSW) - 4 (E) Full-latch 10 kΩ or higher
6 (DLSW) - 4 (E) Half-latch 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK

3.CHECK WIRE HARNESS (BACK DOOR LOCK - POWER BACK DOOR UNIT AND BODY GROUND)
U188670E01
0.054,0.024 1.544,0.171 1.489,0.147 10 Wire Harness Side: 1.126,0.781 2.134,0.936 1.008,0.156 10 Back Door Lock 0.221,1.66 0.534,1.820 0.313,0.161 10 S12 0.825,2.476 2.393,2.820 1.568,0.343 10 Power Back Door Unit (Power Back Door ECU) 0.143,3.734 0.452,3.881 0.309,0.147 10 M24 2.29,1.929 2.756,2.076 0.466,0.147 10 E 0.627,2.163 1.093,2.309 0.466,0.147 10 ULSW 2.264,2.163 2.731,2.309 0.466,0.147 10 DLSW 1.795,4.404 2.140,4.555 0.346,0.151 10 HAF 2.316,4.399 2.657,4.545 0.341,0.147 10 POS 1.985,4.366 2.153,4.103 false 2.411,4.103 2.492,4.378 false 1.169,2.247 1.551,2.166 false 1.904,2.157 2.243,2.234 false 1.856,1.921 2.234,2.002 false

a.

Disconnect the S12 door lock connector.


b.

Disconnect the M24 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
S12-5 (ULSW) - M24-22 (HAF) Below 1 Ω
S12-6 (DLSW) - M24-24 (POS) Below 1 Ω
S12-4 (E) - Body ground Below 1 Ω
S12-5 (ULSW) - Body ground 10 kΩ or higher
S12-6 (DLSW) - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR