Home › Vehicle Interior › ENGINE HOOD / DOOR › POWER BACK DOOR SYSTEM
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292031 POWER BACK DOOR SYSTEM J

ENGINE HOOD / DOOR  POWER BACK DOOR SYSTEM  Power Back Door Closer Switch Circuit  


DESCRIPTION

The power back door closer switch only turns on while the switch is being pressed, and turns off when the switch is released.

When the power back door closer switch is on, a power back door close request signal is input to the power back door ECU to close the back door.

WIRING DIAGRAM

B144402E25
3.37,0.57 3.687,0.719 0.318,0.149 10 3 5.639,0.445 6.034,0.629 0.394,0.184 10 DS1 1.933,0.943 4.150,1.289 2.216,0.346 10 Power Back Door Closer Switch 2.256,0.586 2.393,0.772 0.137,0.186 10 4 5.359,1.315 5.656,1.490 0.297,0.175 10 M24 5.371,1.497 6.918,1.826 1.547,0.330 10 Power Back Door Unit (Power Back Door ECU) 5.399,0.584 5.633,0.744 0.235,0.161 10 4 1.943,0.813 2.242,0.955 0.299,0.142 10 S13

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (POWER BACK DOOR CLOSER SWITCH)
a.

Check the Data List for proper functioning of the power back door closer switch.

Power back door unit (Power back door ECU):
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
PBD Close SW Power back door closer switch signal / ON or OFF ON: Power back door closer switch ON
OFF: Power back door closer switch OFF
-


OK:

The display is as specified in the normal condition.




NG

2.INSPECT POWER BACK DOOR CLOSER SWITCH

OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT POWER BACK DOOR CLOSER SWITCH
B138229E01
0.158,2.092 1.017,2.253 0.860,0.161 10 Pushed (ON)

a.

Remove the power back door closer switch.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Switch Condition Specified Condition
3 - 4 Pushed (ON) Below 1 Ω
3 - 4 Free (OFF) 10 kΩ or higher




OK

3.CHECK WIRE HARNESS (POWER BACK DOOR CLOSER SWITCH - POWER BACK DOOR UNIT AND BODY GROUND)

NG

REPLACE POWER BACK DOOR CLOSER SWITCH

3.CHECK WIRE HARNESS (POWER BACK DOOR CLOSER SWITCH - POWER BACK DOOR UNIT AND BODY GROUND)
U189871E03
1.417,3.969 1.188,4.406 false 0.042,0.01 1.438,0.156 1.396,0.146 10 false Wire Harness Side: 0.677,0.948 2.677,1.104 2,0.156 10 false Power Back Door Closer Switch 0.146,3.792 0.49,3.99 0.344,0.198 10 false M24 0.448,1.979 0.729,2.188 0.281,0.208 10 false S13 0.979,4.417 1.344,4.573 0.365,0.156 10 false DS1 0.896,2.75 2.448,3.073 1.552,0.323 10 false Power Back Door Unit (Power Back Door ECU)

a.

Disconnect the S13 switch connector.


b.

Disconnect the M24 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
S13-3 - M24-4 (DS1) Below 1 Ω
S13-4 - Body ground Below 1 Ω
S13-3 - Body ground 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR