Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM24M0E _51 Engine / Hybrid System _059570 CRUISE CONTROL _0292039 CRUISE CONTROL SYSTEM D

CRUISE CONTROL  CRUISE CONTROL SYSTEM  SYSTEM DESCRIPTION  


CRUISE CONTROL SYSTEM


This system is controlled by the ECM, and is activated by the throttle position sensor and motor. The ECM controls the following functions: ON-OFF, - / SET, + / RES, CANCEL vehicle speed operation, motor output control, and overdrive control.

·

The ECM compares the driving vehicle speed from the combination meter with the stored vehicle speed set through the cruise control main switch. The ECM controls the throttle valve motor of the throttle body to close the valve when the driving speed is less than the stored speed.

·

The ECM receives signals such as ON-OFF, -/SET, +/RES, and CANCEL from the cruise control main switch.

·

The ECM illuminates the combination meter CRUISE indicator light when it receives the cruise control main switch on signal.

·

The ECM cancels the cruise control system when the brake pedal is depressed and the ECM receives the stop light switch signal.

·

The ECM cancels the cruise control system when moving the shift lever to any position other than D, or during sequential shift mode, the shift lever is moved from S (4, 3 ) to "-" (2, 1) and the ECM receives the park/neutral position switch signal. (U241E Automatic transaxle)

·

The ECM cancels the cruise control system when moving the shift lever to any position other than D, or during sequential shift mode, the shift lever is moved from S (6, 5, 4) to "-" (3, 2, 1) and the ECM receives the park/neutral position switch signal. (U660E Automatic transaxle)

·

The ECM cancels the cruise control system when moving the shift lever to any position other than D, or during sequential shift mode, the shift lever is moved from M (7, 6, 5, 4) to "-" (3, 2, 1) and the ECM receives the park/neutral position switch signal. (K112 Continuously variable transaxle)



LIMIT CONTROL


a.

Low speed limit

The lowest possible limit of the speed setting range is set at approximately 40 km/h (25 mph). The cruise control system cannot be set when the driving vehicle speed is below the low speed limit.

Cruise control operation will be automatically canceled and the set speed is stored in memory when the vehicle speed decreases below the low speed limit 40 km/h (25 mph) while the cruise control is operating.


b.

High speed limit

The highest possible limit of the speed setting range is set at approximately 200 km/h (125 mph) for Automatic transaxle model, 100 km/h (62 mph) for Continuously variable transaxle model. The cruise control system cannot be set when the driving vehicle speed is over the high speed limit.

Also, +/RES cannot be used to increase speed beyond the high speed limit.



OPERATION OF CRUISE CONTROL


The cruise control main switch operates 7 functions:

SET, COAST, TAP-DOWN, RESUME, ACCELERATION (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN and COAST functions, and the RESUME, TAP-UP and ACCEL functions are operated with the same switch.

The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it.

a.

SET CONTROL

Vehicle speed is stored and constant speed control is maintained when pushing the switch to -/SET while driving with the cruise control main switch ON (the CRUISE main indicator light is illuminated), and the vehicle speed is within the set speed range (between the low and high speed limits).


b.

COAST CONTROL

The ECM changes the cruise control demand throttle angle to 0° and decelerates the vehicle when -/SET on the cruise control main switch is pressed and held while the cruise control system is operating. When the cruise control main switch is released from -/SET, the vehicle speed is stored and constant speed control is maintained.

HINT:

The throttle valve is not fully closed due to idle speed control, etc.



c.

TAP-DOWN CONTROL

When tapping down the cruise control main switch to -/SET (0.6 seconds or less) while the cruise control system is in operation, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). When the cruise control main switch is released from -/SET and the difference between the driving and stored vehicle speed is more than 5 km/h (3 mph), the vehicle speed is stored and constant speed control is maintained.


d.

ACCEL CONTROL

The throttle valve motor of the throttle position sensor and motor is instructed by the ECM to open the throttle valve when +/RES on the cruise control main switch is pressed and held while the cruise control system is operating. When the cruise control main switch is released from +/RES, the vehicle speed is stored and constant speed is maintained.


e.

TAP-UP CONTROL

When tapping up the cruise control main switch to +/RES (0.6 seconds or less) while the cruise control system is in operation, the stored vehicle speed increases each time by approximately 1.6 km/h (1 mph). However, when the difference between the driving and the stored vehicle speed is more than 5 km/h (approximately 3 mph), the stored vehicle speed will not be changed.


f.

RESUME CONTROL

If the cruise control operation was canceled and if the driving speed is within the set speed range, setting the cruise control main switch to +/RES restores the vehicle speed memorized at the time of cancellation, and constant speed is maintained.

HINT:
·

The cruise control operation can be canceled through one of the following methods: by operating the stop light switch or CANCEL switch; moving the shift lever from D to N; or in sequential shift mode, moving the shift lever from S (4, 3) to "-" (2, 1). (U241E Automatic transaxle)

·

The cruise control operation can be canceled through one of the following methods: by operating the stop light switch or CANCEL switch; moving the shift lever from D to N; or in sequential shift mode, moving the shift lever from S (6, 5, 4) to "-" (3, 2, 1). (U660E Automatic transaxle)

·

The cruise control operation can be canceled through one of the following methods: by operating the stop light switch or CANCEL switch; moving the shift lever from D to N; or in sequential shift mode, moving the shift lever from M (7, 6, 5, 4) to "-" (3, 2, 1). (K112 Continuously variable transaxle)




g.

OVERDRIVE CONTROL

·

Overdrive may cancel automatically when using cruise control while driving on inclined roads, etc.

·

After overdrive is canceled, if the system determines that the road is no longer inclined based on throttle opening information, overdrive will be restored.

·

If overdrive was canceled during ACCEL or RESUME operation, overdrive will be restored after the ACCEL or RESUME operation is completed.



h.

CANCEL CONTROL

i.

Manual cancel

Performing any of the following cancels the cruise control system (the stored vehicle speed in the ECM is maintained).

·

Depressing the brake pedal

·

Setting the cruise control main switch to CANCEL

·

Turning the cruise control main switch OFF (set speed is not stored in memory).

·

Moving the shift lever to any position other than D, during sequential shift mode from S (4, 3) to "-" (2, 1). (U241E Automatic transaxle)

·

Moving the shift lever to any position other than D, during sequential shift mode from S (6, 5, 4) to "-" (3, 2, 1). (U660E Automatic transaxle)

·

Moving the shift lever to any position other than D, during sequential shift mode from M (7, 6, 5, 4) to "-" (3, 2, 1). (K112 Continuously variable transaxle)



ii.

Auto cancel

If any of the conditions below are met, the cruise control operation is canceled.

·

Vehicle speed decreases to less than the low speed limit (the set speed is not erased; it is possible to reset or resume speed) for Automatic transaxle model.

·

Vehicle speed decreases to less than the low speed limit (the set speed is erased) for Continuously transaxle model.

·

While operating the cruise control during driving, if the VSC operates, the cruise control operation is canceled (the set speed is stored in memory).

·

Vehicle speed is 16 km/h (10 mph) less than the set speed (set speed is erased).



iii.

Other cancellation operations

·

When the VSC operates while using cruise control, cruise control will be canceled (speed setting is saved in memory).