Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059570 CRUISE CONTROL _0292039 CRUISE CONTROL SYSTEM D

CRUISE CONTROL  CRUISE CONTROL SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


The ECM controls the functions of the cruise control system on this vehicle. Cruise control data or DTCs can be read from the DLC3 of the vehicle. When trouble occurs with the cruise control, check that the CRUISE main indicator light does not turn on but DTC inspection is performed.

Therefore when there seems to be a problem with the cruise control, use the intelligent tester or SST to check and troubleshoot it.


CHECK DLC3


a.
H103023E07
1.708,1.875 1.948,1.469 true 1.563,0.917 1.208,0.438 true 1.76,0.927 1.542,0.448 true 1.948,0.927 2.031,0.448 true 2.135,0.927 2.427,0.458 true 2.458,1.896 2.313,1.479 true 1.031,0.25 1.281,0.427 0.25,0.177 10 false CG 1.427,1.906 1.896,2.094 0.469,0.188 10 false CANL 1.396,0.25 1.646,0.427 0.25,0.177 10 false SG 1.813,0.229 2.271,0.396 0.458,0.167 10 false CANH 2.417,0.229 2.677,0.406 0.26,0.177 10 false SIL 2.333,1.917 2.802,2.104 0.469,0.188 10 false BAT

The ECM uses ISO 15765-4 for communication.

The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

Symbols (Terminals No.) Terminal Description Condition Specified Condition
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 10 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off* 54 to 69 Ω
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off* 6 kΩ or higher
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off* 200 Ω or higher
CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off* 6 kΩ or higher
CANL (6) - CG (4) LOW-level CAN bus line Ignition switch off* 200 Ω or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.


HINT:
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

·

If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.

·

If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.





CHECK INDICATOR


a.

Turn the ignition switch on (IG).


b.

Check that the CRUISE main indicator light turns on when the cruise control main switch is turned ON, and that the indicator light turns off when the main switch is turned OFF.

HINT:
·

If the indicator check result is not normal, proceed to troubleshooting for the combination meter section (see page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·
BE04034E84
0.073,0.094 1.896,0.292 1.823,0.198 10 false CRUISE Main Indicator Light 0.625,0.552 1.146,0.75 0.521,0.198 10 false 1.5 sec. 1.76,0.542 2.271,0.74 0.51,0.198 10 false 0.5 sec. 0.135,1.125 0.375,1.323 0.24,0.198 10 false ON 0.146,1.677 0.448,1.875 0.302,0.198 10 false OFF

If a malfunction occurs in the speed sensor or stop light switch, etc., during cruise control driving, the ECM activates the AUTO CANCEL of the cruise control and turns ON and OFF the CRUISE main indicator light to inform the driver of a malfunction. At the same time, the malfunction is stored in memory as a diagnostic trouble code (for LHD).

·

While driving with the cruise control system controlling vehicle speed, the ECM will automatically cancel control of vehicle speed by the cruise control system when a malfunction occurs in one of the following: vehicle speed sensors, stop light switch, or other related parts. When control of vehicle speed by the cruise control system is automatically canceled, the cruise control indicator turns off and a warning message is displayed. At the same time, a DTC is stored (for RHD).