Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059570 CRUISE CONTROL _0292039 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Stop Light Switch Circuit Malfunction  


DESCRIPTION

While driving with the cruise control on, if the ECM detects that the brake pedal is depressed, the cruise control operation will be canceled. The stop light switch sends brake pedal status signals to the ECM. When the brake pedal is not depressed, terminal ST1- is equal to the positive (+) battery voltage and terminal STP is below 1 V. When the brake pedal is depressed, the ECM cancels cruise control operation. The ECM outputs this DTC when the voltage of terminals ST1- and STP are both below 1 V for 0.5 seconds or more at the same time.

At this time, the set speed is erased, the cruise control operation is canceled, and the power indicator blinks until the main switch is pushed OFF. Cruise control operation is prohibited until the main switch is pushed ON again.

DTC No. DTC Detection Condition Trouble Are
P0571 When both conditions below are met:
·

Voltage of terminal STP is less than 1 V for 0.5 seconds or more

·

Voltage of terminal ST1 - is less than 1 V for 0.5 seconds or more


·

Stop light switch circuit

·

Stop light switch

·

ECM



WIRING DIAGRAM

U189889E02
6.198,4.375 6.615,4.885 0.417,0.51 10 false A7 6.135,1.594 6.656,1.802 0.521,0.208 10 false ST1- 6.125,0.823 6.604,1.01 0.479,0.188 10 false STP 5.781,0.708 5.958,0.885 0.177,0.177 10 false 36 5.802,1.448 5.979,1.656 0.177,0.208 10 false 35 4.708,1.448 4.885,1.646 0.177,0.198 10 false 3 4.698,0.698 4.865,0.885 0.167,0.188 10 false 1 3.188,1.479 3.365,1.667 0.177,0.188 10 false 4 3.208,0.698 3.365,0.917 0.156,0.219 10 false 2 3.448,2.156 4.635,2.719 1.188,0.563 10 false A1 2.427,1.802 2.719,2.073 0.292,0.271 10 false IGN 2.375,1.042 2.844,1.25 0.469,0.208 10 false STOP 1.823,2.615 3.427,2.771 1.604,0.156 10 false from IG2 Relay*1 1.708,3.573 3.073,3.75 1.365,0.177 10 false from Battery 0.333,4.969 3.604,5.156 3.271,0.188 10 false *1: w/ Smart Entry and Start System 1.823,2.969 3.344,3.135 1.521,0.167 10 false from Ignition Switch*2 0.333,5.292 3.583,5.5 3.25,0.208 10 false *2: w/o Smart Entry and Start System 3.448,2.323 4.635,2.885 1.188,0.563 10 false Stop Light Switch 6.198,4.542 6.615,5.052 0.417,0.51 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Check the Data List for proper functioning of the stop light switch.

Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Stp Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal is depressed
OFF: Brake pedal is released
-

OK:

Display changes according to brake pedal operation described in above table.


Result:
Result Proceed to
NG A
OK
(for 2AZ-FE)
B
OK
(for 2GR-FE)
C




A

2.INSPECT STOP LIGHT SWITCH

B

C

2.INSPECT STOP LIGHT SWITCH
A167698E02
0.049,0.83 0.780,0.991 0.731,0.161 10 Not pushed 2.086,0.83 2.583,0.996 0.497,0.166 10 Pushed 0.045,0.032 2.515,0.216 2.470,0.184 10 Component without harness connected: 0.045,0.233 1.876,0.394 1.831,0.161 10 (Stop Light Switch Assembly) 2.377,2.052 2.484,2.200 0.107,0.148 10 1 1.004,2.052 1.121,2.209 0.116,0.157 10 2 1.004,2.733 1.103,2.877 0.098,0.143 10 4 2.377,2.733 2.484,2.881 0.107,0.148 10 3 1.127,2.131 1.637,2.3 false 1.133,2.806 1.624,2.532 false 1.897,2.532 2.36,2.8 false 1.886,2.301 2.344,2.147 false

a.

Remove the stop light switch.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed Below 1 Ω
3 - 4 Pushed
1 - 2 Pushed 10 kΩ or higher
3 - 4 Not pushed




OK

3.CHECK WIRE HARNESS (SWITCH - BATTERY)

NG

REPLACE STOP LIGHT SWITCH

3.CHECK WIRE HARNESS (SWITCH - BATTERY)
U188468E02
0.073,0.063 2.323,0.458 2.25,0.396 10 false Front view of wire harness connector: (to Stop Light Switch Assembly) 0.677,2.385 0.896,2.521 0.219,0.135 10 false A1

a.

Disconnect the stop light switch connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Switch Condition Specified Condition
A1-4 - Body ground Ignition switch ON 10 to 14 V
A1-2 - Body ground Always




OK

4.CHECK WIRE HARNESS (ECM - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (ECM - BATTERY)
U189823E01
0.034,0.034 1.763,0.259 1.729,0.225 10 Wire Harness Side: 0.287,1.272 0.482,1.414 0.194,0.142 10 A7 0.486,0.516 0.985,0.703 0.499,0.187 10 ST1- 2.624,0.374 3.203,0.553 0.580,0.180 10 STP 0.915,0.611 1.251,0.611 1.251,0.611 1.852,1.482 false 1.942,1.479 2.361,0.473 2.361,0.473 2.574,0.473 false

a.

Disconnect the ECM connector.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Switch Condition Specified Condition
A7-36 (STP) - Body ground Depressed 10 to 14 V
A7-35 (ST1-) - Body ground Released
A7-36 (STP) - Body ground Released Below 1 V
A7-35 (ST1-) - Body ground Depressed


Result:
Result Proceed to
NG A
OK
(for 2AZ-FE)
B
OK
(for 2GR-FE)
C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C