Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM U

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)


U188402E02
5.76,3.875 5.896,2.354 false 5.948,2.188 7.021,2.49 1.073,0.302 10 false Main Body ECU 2.49,2.125 4.813,2.302 2.323,0.177 10 false Instrument Panel Junction Block LH 2.688,4.135 3.25,4.479 0.563,0.344 10 false 4A 4.302,5.479 4.865,5.823 0.563,0.344 10 false 4K 6.406,4.24 6.969,4.583 0.563,0.344 10 false G57 6.406,4.99 6.969,5.333 0.563,0.344 10 false G58 6.406,5.625 6.969,5.969 0.563,0.344 10 false G59 6.406,6.094 6.969,6.438 0.563,0.344 10 false G60

a.

Disconnect the G57, G58 and G59 main body ECU connectors.


b.

Disconnect the 4A instrument panel junction block LH connector.


c.

Measure the voltage and resistance of the wire harness side connector.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G57-6 (AM1) - Body ground SB - Body ground +B power supply Always 11 to 14 V
G57-16 (SSW2) - Body ground G - Body ground Engine switch signal Engine switch pushed Below 1 Ω
G57-16 (SSW2) - Body ground G - Body ground Engine switch signal Engine switch not pushed 10 kΩ or higher
G57-17 (SSW1) - Body ground P - Body ground Engine switch signal Engine switch pushed Below 1 Ω
G57-17 (SSW1) - Body ground P - Body ground Engine switch signal Engine switch not pushed 10 kΩ or higher
G58-1 (AM2) - Body ground SB - Body ground +B power supply Always 11 to 14 V
G59-1 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
G59-5 (CANH) - Body ground B - Body ground CAN Line Always 10 kΩ or higher
G59-6 (CANL) - Body ground W - Body ground CAN Line Always 10 kΩ or higher
4A-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
4A-20 (LIN1) - Body ground R - Body ground LIN line Always 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Reconnect the ECU connectors.


e.

Measure the voltage of the connector.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G57-3 (IG1D) - G59-1 (GND1) R - W-B IG1 signal Engine switch on (IG) Output voltage at terminal AM1 or AM2 is -2 V or more.
G57-3 (IG1D) - G59-1 (GND1) R - W-B IG1 signal Engine switch on (ACC) Below 1 V
G57-8 (STR) - G59-1 (GND1) G - W-B Park/neutral position switch Engine switch on (IG), shift lever except P or N position → P or N position Below 2 V → Pulse generation *3
G57-14 (INDW) - G59-1 (GND1) GR - W-B Warning signal Shift lever P position, engine switch on (ACC, IG) Output voltage at terminal AM1 or AM2 is -3 V or more.
G57-15 (INDS) - G59-1 (GND1) Y - W-B Vehicle condition signal Brake pedal depressed, shift lever P position Output voltage at terminal AM1 or AM2 is -3 V or more.
G57-18 (SLP) - G59-1 (GND1) Y - W-B Steering lock actuator position signal Steering lock is locked Pulse generation
(See waveform 3)
G57-18 (SLP) - G59-1 (GND1) Y - W-B Steering lock actuator position signal Steering lock is released Pulse generation
(See waveform 3)
G57-19 (SLR+) - G59-1 (GND1) L - W-B Steering lock motor signal Steering lock motor operating Below 1 V
G57-19 (SLR+) - G59-1 (GND1) L - W-B Steering lock motor signal Steering lock motor does not operate Output voltage at terminal AM1 or AM2 is -2 V or more.
G57-22 (ACCD) - G59-1 (GND1) GR - W-B ACC signal Engine switch on (ACC) Output voltage at terminal AM1 or AM2 is -2 V or more.
G57-22 (ACCD) - G59-1 (GND1) GR - W-B ACC signal Engine switch off Below 1 V
G57-25 (SWIL) - G59-1 (GND1) SB - W-B Illumination signal Light control switch TAIL or HEAD Output voltage at terminal AM1 or AM2 is -2 V or more.
G58-3 (ACCR) - G59-1 (GND1) L - W-B Starter assist signal
(ACC cut signal)
Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG) 0.1 to 0.8 V *1
→ Output voltage at terminal AM1 or AM2 is -2 V or more.
G58-11 (IG2D) - G59-1 (GND1) G - W-B IG2 signal Engine switch on (IG) Output voltage at terminal AM1 or AM2 is -2 V or more.
G58-11 (IG2D) - G59-1 (GND1) G - W-B IG2 signal Engine switch on (ACC) Below 1 V
G59-8 (TACH) - G59-1 (GND1) R - W-B Tachometer signal Engine running Pulse generation
(See waveform 2)
G59-9 (SPD) - G59-1 (GND1) W - W-B Vehicle speed signal Engine switch on (IG), rotate rear wheel slowly Pulse generation
(See waveform 1)
G60-2 (P) - G59-1 (GND1) G - W-B Shift lock signal Shift lever P position Output voltage at terminal AM1 or AM2 is -2 V or more.
G60-2 (P) - G59-1 (GND1) G - W-B Shift lock signal Shift lever not P position Below 1.5 V
G60-4 (STSW) - G59-1 (GND1) P - W-B Starter activation request signal Brake pedal depressed, engine switch held on (ST) Output voltage at terminal AM1 or AM2 is -2 V or more.
G60-6 (STR2) - G59-1 (GND1) SB - W-B Starter signal (Sub) Brake pedal depressed, shift lever P or N position, engine switch on (ST) Output voltage at terminal AM1 or AM2 is -3.5 V or more. *2
4A-26 (ACC) - Body ground GR - Body ground ACC power supply Always 11 to 14 V
4K-7 (STP) - G59-1 (GND1) L - W-B Stop light signal Brake pedal depressed Output voltage at terminal AM1 or AM2 is -2 V or more.
4K-7 (STP) - G59-1 (GND1) L - W-B Stop light signal Brake pedal released Below 1 V
4M-1 (IG) - Body ground W - Body ground IG power supply Always 11 to 14 V

HINT:

*1: Voltage is output only when the engine is cranking.

*2: Voltage is output for 0.3 seconds when the engine is cranking to start. Disconnect the D1 connector from the ECM and ST CUT relay before measuring the voltage.

*3: Remove the ST CUT relay before measuring the voltage.


If the result is not as specified, the ECU may have a malfunction.


f.

Using an oscilloscope, check the signal waveform of the ECU.

i.
I042329E26
2.833,1.24 3.208,1.615 0.375,0.375 10 false GND

Waveform 1

Waveform 1 (Reference):
Terminal No. G59-9 (SPD) - G59-1 (GND1)
Tool Setting 5 V/DIV., 10 ms./DIV.
Vehicle Condition Driving at approx. 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the wavelength shortens.



ii.
I042330E34
2.896,1.229 3.26,1.427 0.365,0.198 10 false GND

Waveform 2

Waveform 2 (Reference):
Terminal No. G59-8 (TACH) - G59-1 (GND1)
Tool Setting 5 V/DIV., 10 ms./DIV.
Vehicle Condition Engine idling

HINT:

As the engine revolution speed increases, the wavelength shortens.



iii.
A378304E01
0.479,0.948 0.479,0.698 0.479,0.698 0.729,0.583 false 2.208,1.948 2.042,1.948 2.042,1.948 1.979,1.667 false 2.927,1.573 3.344,1.813 0.417,0.24 10 false GND 2.26,1.875 2.771,2.104 0.51,0.229 10 false Unlock 0.354,0.99 0.771,1.229 0.417,0.24 10 false Lock

Waveform 3

Waveform 3 (Reference):
Terminal No. G57-18 (SLP) - G59-1 (GND1)
Tool Setting 2 V/DIV., 100 ms./DIV.
Vehicle Condition Steering lock/unlock




CHECK CERTIFICATION ECU


U188569E02
3.49,0.281 3.771,0.448 0.281,0.167 10 false G29

a.

Disconnect the G29 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G29-1 (+B) - Body ground BE - Body ground +B power supply Always 11 to 14 V
G29-10 (LIN) - Body ground R - Body ground LIN line Always 10 kΩ or higher
G29-17 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the ECU connector.


d.

Measure the voltage of the connector.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G29-18 (IG) - Body ground B - Body ground Ignition power supply Engine switch on (IG) 11 to 14 V
G29-18 (IG) - Body ground B - Body ground Ignition power supply Engine switch off Below 1 V

If the result is not as specified, the ECU may have a malfunction.



CHECK ECM


U188255E02
2.188,0.375 2.385,0.542 0.198,0.167 10 false D1 5.323,0.375 5.51,0.542 0.188,0.167 10 false A7

a.

Disconnect the D1 and A7 ECM connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
A7-1 (+B2) - Body ground B - Body ground Power source of ECM Engine switch on (IG) 11 to 14 V
A7-2 (+B) - Body ground B - Body ground Power source of ECM Engine switch on (IG) 11 to 14 V
A7-28 (IGSW) - Body ground BE - Body ground Engine switch signal Engine switch on (IG) 11 to 14 V
D1-20 (ME01) - Body ground BR - Body ground Ground Always Below 1 Ω
D1-21 (E02) - Body ground W-B - Body ground Ground Always Below 1 Ω
D1-22 (E01) - Body ground BR - Body ground Ground Always Below 1 Ω
D1-23 (E04) - Body ground W-B - Body ground Ground Always Below 1 Ω
D1-46 (E05) - Body ground BR - Body ground Ground Always Below 1 Ω
D1-81 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
D1-104 (E03) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the ECM connectors.


d.

Measure the voltage of the connectors.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
A7-13 (ACCR) - D1-81 (E1) GR - BR ACC relay cut signal (output) Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG) 0.1 to 0.8 V *1 → Output voltage at terminal AM1 or AM2 is -2 V or more.
A7-14 (STSW) - D1-81 (E1) P - BR Starter activation request signal Brake pedal depressed, engine switch held (on) Output voltage at terminal AM1 or AM2 is -2 V or more.
A7-15 (TACH) - D1-81 (E1) B - BR Engine revolution signal (output) Idling Pulse generation (see waveform 1)
A7-36 (STP) - D1-81 (E1) L - BR Stop light switch signal (input) Brake pedal depressed 7.5 to 14 V
A7-36 (STP) - D1-81 (E1) L - BR Stop light switch signal (input) Brake pedal released Below 1.5 V
A7-48 (STA) - D1-81 (E1) B - BR Starter relay operation signal Cranking 11 to 14 V
D1-62 (NSW) - D1-81 (E1) L-B - BR Park/neutral position switch Shift lever P or N position → except P or N position Below 1 V → Pulse generation
D1-63 (STAR) - D1-81 (E1) G-R - BR Starter signal (Main) Brake pedal depressed, shift lever P or N position, engine switch on (ST) 11 to 14 V

HINT:

*1: Voltage is output only when the engine is cranking.


If the result is not as specified, the ECM may have a malfunction.


e.
I042330E34
2.896,1.229 3.26,1.427 0.365,0.198 10 false GND

Using an oscilloscope, check the signal waveform of the ECM.

Waveform 1 (Reference):
Terminal No. A7-15 (TACH) - D1-81 (E1)
Tool Setting 5 V/DIV., 10 ms./DIV.
Vehicle Condition Engine idling

HINT:

As the vehicle speed increases, the wavelength shortens.




CHECK STEERING LOCK ECU


U188553E02
3.438,0.344 3.719,0.51 0.281,0.167 10 false G32

a.

Disconnect the G32 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G32-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
G32-2 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
G32-6 (IG2) - Body ground B - Body ground Ignition power supply Engine switch on (IG) 11 to 14 V
G32-6 (IG2) - Body ground B - Body ground Ignition power supply Engine switch off Below 1 V
G32-7 (B) - Body ground B - Body ground +B power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G32 ECU connector.


d.

Measure the voltage of the connector.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G32-4 (SLP1) - G32-1 (GND) Y - W-B Steering lock actuator position signal Steering is locked 11 to 14 V
G32-4 (SLP1) - G32-1 (GND) Y - W-B Steering lock actuator position signal Steering is released Below 1 V

If the result is not as specified, the ECU may have a malfunction.