Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM D

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


a.

Push-button start function data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the function seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform repairs.



CHECK DLC3


H103023E07
1.708,1.875 1.948,1.469 true 1.563,0.917 1.208,0.438 true 1.76,0.927 1.542,0.448 true 1.948,0.927 2.031,0.448 true 2.135,0.927 2.427,0.458 true 2.458,1.896 2.313,1.479 true 1.031,0.25 1.281,0.427 0.25,0.177 10 false CG 1.427,1.906 1.896,2.094 0.469,0.188 10 false CANL 1.396,0.25 1.646,0.427 0.25,0.177 10 false SG 1.813,0.229 2.271,0.396 0.458,0.167 10 false CANH 2.417,0.229 2.677,0.406 0.26,0.177 10 false SIL 2.333,1.917 2.802,2.104 0.469,0.188 10 false BAT

HINT:

The ECU uses ISO 15765-4 communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.


Tester Connection Terminal Description Condition Specified Condition
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Engine switch OFF* 56 to 69 Ω
CANH (6) - CG (4) HIGH-level CAN bus line Engine switch OFF* 200 Ω or higher
CANL (14) - CG (4) LOW-level CAN bus line Engine switch OFF* 200 Ω or higher
CANH (6) - BAT (16) HIGH-level CAN bus line Engine switch OFF* 6 kΩ or higher
CANL (14) - BAT (16) LOW-level CAN bus line Engine switch OFF* 6 kΩ or higher

NOTICE:

*: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches or the doors.


If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

HINT:

Connect the cable of the intelligent tester to the DLC3, turn the engine switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

·
B135940E05
2.359,2.15 2.758,2.306 0.399,0.156 10 DLC3 1.877,1.667 2.51,2.127 false 0.64,2.864 1.692,3.019 1.052,0.156 10 Intelligent Tester 0.7,2.619 1.035,2.838 false


·

If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.

·

If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.




INSPECT BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.