Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM U

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.


a.

Connect the intelligent tester to the DLC3.

When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 or less second intervals until communication between the tester and vehicle starts.


b.

Turn the engine switch on (IG).


c.

Read the DATA LIST.

Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Engine switch on (ACC) / ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
-
IG SW Engine switch on (IG) / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
St SW1 Start switch 1 / ON or OFF ON: Engine switch is pushed
OFF: Engine switch is not pushed
-
St SW2 Start switch 2 / ON or OFF ON: Engine switch is pushed
OFF: Engine switch is not pushed
-
Str Unlock SW Steering lock condition / ON or OFF ON: Steering is unlocked (Engine switch on (ACC))
OFF: Steering is locked (Engine switch off)
-
N SW / C SW Neutral start switch / ON or OFF ON: Shift position is P or N
OFF: Shift position is neither P nor N
-
Shift P Sig Shift P position signal / ON or OFF ON: Shift position is P
OFF: Shift position is not P
-
Vehicle Spd Sig Vehicle speed signal / STOP or RUN STOP: Vehicle is stopped
RUN: Vehicle is running
-
E/G Cond Engine condition / STOP or RUN STOP: Engine is stopped
RUN: Engine is running
-
IG1 Relay Mon1 IG1 relay monitor (outer) / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
IG2 Relay Mon1 IG2 relay monitor (outer) / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
IG1 Relay Mon2 IG1 relay monitor (inner) / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
IG2 Relay Mon2 IG2 relay monitor (inner) / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
ACC Relay Mon ACC relay monitor / ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
-
Ratch Circuit Ratch circuit / ON or OFF ON: Engine switch on (IG) or engine running
OFF: Engine switch off or on (ACC)
-
Start Req Sig Starter request signal monitor / ON or OFF ON: ST relay is ON
OFF: ST relay is OFF
Engine switch pressed and held with shift lever in P or N
Pwr Cond Power supply condition / ALL, ACC ON, IG1 IG2, ST ON ALL: All relays are OFF
ACC ON: ACC relay is ON
IG1: IG1 relay is ON
IG2: IG2 relay is ON
ST ON: ST request signal is ON
-
ACC Cut Sig ACC relay cut signal / ON or OFF ON: Engine is cranking
OFF: Engine is not cranking
-
St Relay Mon STARTER relay monitor / ON or OFF ON: Engine is cranking
OFF: Engine is not cranking
Engine is cranking with engine switch on (IG) and shift lever in P or N
Comm Entry&Start Communication for certification ECU / OK or STOP OK: Communication
STOP: No communication
-



PERFORM ACTIVE TEST


HINT:

Performing the intelligent tester's ACTIVE TEST allows the relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Perform the ACTIVE TEST according to the display on the tester.



Body:
Tester Display Test Part Control Range Diagnostic Note
Lighting Ind Indicator for lighting ON / OFF -
Ind Condition Engine switch indicator Green / Amber / No Sig -
S Lock Pwr Power supply for steering lock ECU ON / OFF -