Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM C

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  B2272  Ignition 1 Monitor Malfunction  


DESCRIPTION

This DTC is output when a malfunction occurs in the IG1D output circuit, which is between the LH-IG relay 1 actuation circuit inside the main body ECU and the LH-IG relay 1.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored. After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2272 LH-IG relay 1 actuation circuit inside main body ECU or other related circuit is malfunctioning
·

Instrument panel junction block LH (Main body ECU)

·

Instrument panel junction block RH

·

Wire harness or connector



WIRING DIAGRAM

B166951E03
2.2,2.669 4.467,2.813 2.267,0.144 10 Instrument Panel Junction Block RH 6.607,4.303 6.901,4.446 0.295,0.144 10 G57 6.158,4.303 6.509,4.446 0.350,0.144 10 IG1D 6.705,4.078 6.815,4.222 0.110,0.144 10 3 5.849,1.611 6.060,1.755 0.211,0.144 10 5D 4.942,1.028 5.408,1.358 0.466,0.330 10 From Battery 3.583,1.939 4.521,2.084 0.938,0.145 10 RH-IG Relay 1 2.369,4.722 3.307,4.867 0.938,0.145 10 LH-IG Relay 2 2.369,6.268 3.307,6.413 0.938,0.145 10 LH-IG Relay 1 2.461,0.414 3.409,0.557 0.948,0.144 10 SEAT HTR RH 2.657,0.82 3.438,0.964 0.781,0.144 10 RH ECU-IG 1.102,0.721 2.104,0.858 1.002,0.137 10 to Each System 1.529,5.4 1.995,5.729 0.466,0.330 10 From Battery 1.548,3.841 2.014,4.171 0.466,0.330 10 From Battery 2.769,1.249 3.300,1.393 0.531,0.144 10 FR WIP 4.782,4.618 5.359,4.949 0.577,0.330 10 to Each System 3.498,5.583 4.533,5.727 1.036,0.144 10 GAUGE NO. 2 3.498,5.205 4.436,5.349 0.938,0.144 10 SEAT HTR LH 3.498,6.027 4.232,6.171 0.735,0.144 10 LH ECU-IG 3.446,3.616 4.505,3.760 1.059,0.144 10 GAUGE NO. 1 3.587,4.05 4.117,4.194 0.531,0.144 10 RR WIP 5.919,1.401 6.029,1.545 0.110,0.144 10 7 0.846,1.611 1.058,1.755 0.211,0.144 10 5A 0.897,1.401 1.008,1.545 0.110,0.144 10 4 0.846,2.265 1.058,2.409 0.211,0.144 10 5D 0.865,2.055 1.040,2.198 0.175,0.144 10 12 0.682,4.394 0.893,4.538 0.211,0.144 10 4D 0.7,4.184 0.875,4.328 0.175,0.144 10 11 0.682,6.655 0.893,6.799 0.211,0.144 10 4A 0.737,6.445 0.839,6.588 0.101,0.144 10 5 1.836,7.068 5.270,7.212 3.434,0.144 10 Instrument Panel Junction Block LH (Main Body ECU)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.
U188713E02
1.625,1.594 2.615,1.76 false 0.135,0.073 2.49,0.448 2.354,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.104,2.375 2.531,2.76 2.427,0.385 10 false Front view of wire harness connector: (to Instrument Panel Junction Block RH) 0.615,1.625 0.896,1.771 0.281,0.146 10 false G57 2.667,1.708 3.083,1.865 0.417,0.156 10 false IG1D 1.708,4.26 1.927,4.406 0.219,0.146 10 false 5D

Disconnect the G57 main body ECU connector.


b.

Disconnect the 5D instrument panel junction block RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified Condition
G57-3 (IG1D) - 5D-7 Always Below 1 Ω
G57-3 (IG1D) or 5D-7 - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the 5A instrument panel junction block RH connector.

U188866E02
1.208,1.635 1.302,2.146 false 5.979,1.625 5.365,2.125 false 5.854,3.708 5.74,4.26 false 1.115,3.677 1.125,4.229 false 0.313,0.406 2.74,0.75 2.427,0.344 10 false Front view of wire harness connector: (to Instrument Panel Junction Block LH) 4.281,0.406 6.708,0.771 2.427,0.365 10 false Front view of wire harness connector: (to Instrument Panel Junction Block RH) 4.281,2.365 6.698,2.719 2.417,0.354 10 false Front view of wire harness connector: (to Instrument Panel Junction Block LH) 0.271,2.365 2.698,2.729 2.427,0.365 10 false Front view of wire harness connector: (to Instrument Panel Junction Block RH) 1.583,1.083 1.771,1.219 0.188,0.135 10 false 4A 5.406,1.083 5.604,1.219 0.198,0.135 10 false 5D 1.583,3.167 1.771,3.302 0.188,0.135 10 false 5A 5.396,3.167 5.604,3.302 0.208,0.135 10 false 4D 1.146,2.146 1.5,2.302 0.354,0.156 10 false 4A-5 0.99,4.281 1.365,4.469 0.375,0.188 10 false 5A-4 5.167,2.146 5.635,2.333 0.469,0.188 10 false 5D-12 5.531,4.281 6,4.469 0.469,0.188 10 false 4D-11


b.

Disconnect the 4A and 4D instrument panel junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified condition
5D-12 - 4D-11 Always Below 1 Ω
5D-12 or 4D-11 - Body ground Always 10 kΩ or higher
5A-4 - Body ground Always Below 1 Ω
4A-5 - Body ground Always Below 1 Ω




OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH
a.

Measure the resistance according the value(s) in the table below.

U188865E02
2.76,1.542 3,1.74 0.24,0.198 10 false 5A 2.781,2.646 3.031,2.813 0.25,0.167 10 false 5D 4.24,1.615 4.542,1.823 0.302,0.208 10 false 5G 4.219,2.344 4.479,2.542 0.26,0.198 10 false 5K 4.24,2.708 4.573,2.948 0.333,0.24 10 false 5L 4.229,3.052 4.531,3.25 0.302,0.198 10 false 5M 5.479,3.042 5.771,3.24 0.292,0.198 10 false 5N

Standard resistance:
Tester connection Condition Specified condition
5D-7 - 5D-12 Always Below 1 Ω
5D-7 - 5A-4 Always Below 1 Ω
5D-7 - Body ground Always 10 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH