CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK LH)
| *A | Instrument Panel Junction Block LH | *B | Main Body ECU |
Disconnect the G57, G58 and G59 main body ECU connectors.
Disconnect the 4A instrument panel junction block LH connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G57-6 (AM1) - Body ground | SB - Body ground | +B power supply | Always | 11 to 14 V |
| G57-16 (SSW2) - Body ground | G - Body ground | Engine switch signal | Engine switch pushed | Below 1 Ω |
| G57-16 (SSW2) - Body ground | G - Body ground | Engine switch signal | Engine switch not pushed | 10 kΩ or higher |
| G57-17 (SSW1) - Body ground | P - Body ground | Engine switch signal | Engine switch pushed | Below 1 Ω |
| G57-17 (SSW1) - Body ground | P - Body ground | Engine switch signal | Engine switch not pushed | 10 kΩ or higher |
| G58-1 (AM2) - Body ground | SB - Body ground | +B power supply | Always | 11 to 14 V |
| G59-1 (GND1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| G59-5 (CANH) - Body ground | B - Body ground | CAN Line | Always | 10 kΩ or higher |
| G59-6 (CANL) - Body ground | W - Body ground | CAN Line | Always | 10 kΩ or higher |
| 4A-3 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 4A-20 (LIN1) - Body ground | R - Body ground | LIN line | Always | 10 kΩ or higher |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the ECU connectors.
Measure the voltage of the connector.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G57-3 (IG1D) - G59-1 (GND1) | R - W-B | IG1 signal | Engine switch on (IG) | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G57-3 (IG1D) - G59-1 (GND1) | R - W-B | IG1 signal | Engine switch on (ACC) | Below 1 V |
| G57-8 (STR) - G59-1 (GND1) | G - W-B | Park/neutral position switch | Engine switch on (IG), shift lever except P or N position → P or N position | Below 2 V → Pulse generation *3 |
| G57-14 (INDW) - G59-1 (GND1) | GR - W-B | Warning signal | Shift lever P position, engine switch on (ACC, IG) | Output voltage at terminal AM1 or AM2 is -3 V or more. |
| G57-15 (INDS) - G59-1 (GND1) | Y - W-B | Vehicle condition signal | Brake pedal depressed, shift lever P position | Output voltage at terminal AM1 or AM2 is -3 V or more. |
| G57-18 (SLP) - G59-1 (GND1) | Y - W-B | Steering lock actuator position signal | Steering lock is locked | Pulse generation
(See waveform 3) |
| G57-18 (SLP) - G59-1 (GND1) | Y - W-B | Steering lock actuator position signal | Steering lock is released | Pulse generation
(See waveform 3) |
| G57-19 (SLR+) - G59-1 (GND1) | L - W-B | Steering lock motor signal | Steering lock motor operating | Below 1 V |
| G57-19 (SLR+) - G59-1 (GND1) | L - W-B | Steering lock motor signal | Steering lock motor does not operate | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G57-22 (ACCD) - G59-1 (GND1) | GR - W-B | ACC signal | Engine switch on (ACC) | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G57-22 (ACCD) - G59-1 (GND1) | GR - W-B | ACC signal | Engine switch off | Below 1 V |
| G57-25 (SWIL) - G59-1 (GND1) | SB - W-B | Illumination signal | Light control switch TAIL or HEAD | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G58-3 (ACCR) - G59-1 (GND1) | L - W-B | Starter assist signal
(ACC cut signal) |
Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG) | 0.1 to 0.8 V *1
→ Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G58-11 (IG2D) - G59-1 (GND1) | G - W-B | IG2 signal | Engine switch on (IG) | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G58-11 (IG2D) - G59-1 (GND1) | G - W-B | IG2 signal | Engine switch on (ACC) | Below 1 V |
| G59-8 (TACH) - G59-1 (GND1) | R - W-B | Tachometer signal | Engine running | Pulse generation
(See waveform 2) |
| G59-9 (SPD) - G59-1 (GND1) | W - W-B | Vehicle speed signal | Engine switch on (IG), rotate rear wheel slowly | Pulse generation
(See waveform 1) |
| G60-2 (P) - G59-1 (GND1) | G - W-B | Shift lock signal | Shift lever P position | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G60-2 (P) - G59-1 (GND1) | G - W-B | Shift lock signal | Shift lever not P position | Below 1.5 V |
| G60-4 (STSW) - G59-1 (GND1) | P - W-B | Starter activation request signal | Brake pedal depressed, engine switch held on (ST) | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| G60-6 (STR2) - G59-1 (GND1) | SB - W-B | Starter signal (Sub) | Brake pedal depressed, shift lever P or N position, engine switch on (ST) | Output voltage at terminal AM1 or AM2 is -3.5 V or more. *2 |
| 4A-26 (ACC) - Body ground | GR - Body ground | ACC power supply | Always | 11 to 14 V |
| 4K-7 (STP) - G59-1 (GND1) | L - W-B | Stop light signal | Brake pedal depressed | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| 4K-7 (STP) - G59-1 (GND1) | L - W-B | Stop light signal | Brake pedal released | Below 1 V |
| 4M-1 (IG) - Body ground | W - Body ground | IG power supply | Always | 11 to 14 V |
*1: Voltage is output only when the engine is cranking.
*2: Voltage is output for 0.3 seconds when the engine is cranking to start. Disconnect the D1 connector from the ECM and ST CUT relay before measuring the voltage.
*3: Remove the ST CUT relay before measuring the voltage.
If the result is not as specified, the ECU may have a malfunction.
Using an oscilloscope, check the signal waveform of the ECU.
Waveform 1
| Terminal No. | G59-9 (SPD) - G59-1 (GND1) |
| Tool Setting | 5 V/DIV., 10 ms./DIV. |
| Vehicle Condition | Driving at approx. 20 km/h (12 mph) |
As the vehicle speed increases, the wavelength shortens.
Waveform 2
| Terminal No. | G59-8 (TACH) - G59-1 (GND1) |
| Tool Setting | 5 V/DIV., 10 ms./DIV. |
| Vehicle Condition | Engine idling |
As the engine revolution speed increases, the wavelength shortens.
Waveform 3
| Terminal No. | G57-18 (SLP) - G59-1 (GND1) |
| Tool Setting | 2 V/DIV., 100 ms./DIV. |
| Vehicle Condition | Steering lock/unlock |
CHECK CERTIFICATION ECU
Disconnect the G29 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G29-1 (+B) - Body ground | BE - Body ground | +B power supply | Always | 11 to 14 V |
| G29-10 (LIN) - Body ground | R - Body ground | LIN line | Always | 10 kΩ or higher |
| G29-17 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the G29 ECU connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G29-18 (IG) - Body ground | B - Body ground | Ignition power supply | Engine switch on (IG) | 11 to 14 V |
| G29-18 (IG) - Body ground | B - Body ground | Ignition power supply | Engine switch off | Below 1 V |
| CLG5 (G29-11) - CG5B (G29-12) | P - V | Indoor electrical key antenna (for front) sensor signal | 30 seconds after driver side door opened and closed, engine switch off | Hz output → no Hz output |
| CLG6 (G29-13) - CG6B (G29-14) | B - Y | Indoor electrical key antenna (for rear1) sensor signal | 30 seconds after driver side door opened and closed, engine switch off | Hz output → no Hz output |
| CLG7 (G29-15) - CG7B (G29-16) | B - G | Indoor electrical key antenna (for rear2) sensor signal | 30 seconds after driver side door opened and closed, engine switch off | Hz output → no Hz output |
| CLG8 (G29-31) - CG8B (G29-32) | BR - GR | Back door electrical key antenna (for outer) sensor signal | With engine switch OFF and doors closed, back door unlock switch OFF → ON | Hz output → no Hz output |
| RCO (G29-29) - E (G29-17) | P - W-B | Door control receiver power source | Engine switch off, all doors closed and transmitter switch not pressed → pressed | Below 1 V → 4.6 to 5.4 V → Below 1 V |
| RSSI (G29-39) - E (G29-17) | BE - W-B | Door control receiver electric wave existence signal | Engine switch off, all doors closed and transmitter switch not pressed → pressed | 10 to 14 V → Below 1 V |
| RDA (G29-38) - E (G29-17) | V - W-B | Door control receiver data input signal | Engine switch off, all doors closed and transmitter switch not pressed → pressed | Below 1 V → 10 to 14 V → Below 1 V |
If the result is not as specified, the ECU may have a malfunction.
CHECK ECM
Disconnect the D1 and A7 ECM connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A7-1 (+B2) - Body ground | B - Body ground | Power source of ECM | Engine switch on (IG) | 11 to 14 V |
| A7-2 (+B) - Body ground | B - Body ground | Power source of ECM | Engine switch on (IG) | 11 to 14 V |
| A7-28 (IGSW) - Body ground | BE - Body ground | Engine switch signal | Engine switch on (IG) | 11 to 14 V |
| D1-20 (ME01) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| D1-21 (E02) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| D1-22 (E01) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| D1-23 (E04) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| D1-46 (E05) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| D1-81 (E1) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| D1-104 (E03) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the ECM connectors.
Measure the voltage of the connectors.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A7-13 (ACCR) - D1-81 (E1) | GR - BR | ACC relay cut signal (output) | Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG) | 0.1 to 0.8 V *1 → Output voltage at terminal AM1 or AM2 is -2 V or more. |
| A7-14 (STSW) - D1-81 (E1) | P - BR | Starter activation request signal | Brake pedal depressed, engine switch held (on) | Output voltage at terminal AM1 or AM2 is -2 V or more. |
| A7-15 (TACH) - D1-81 (E1) | B - BR | Engine revolution signal (output) | Idling | Pulse generation (see waveform 1) |
| A7-36 (STP) - D1-81 (E1) | L - BR | Stop light switch signal (input) | Brake pedal depressed | 7.5 to 14 V |
| A7-36 (STP) - D1-81 (E1) | L - BR | Stop light switch signal (input) | Brake pedal released | Below 1.5 V |
| A7-48 (STA) - D1-81 (E1) | B - BR | Starter relay operation signal | Cranking | 11 to 14 V |
| D1-62 (NSW) - D1-81 (E1) | L-B - BR | Park/neutral position switch | Shift lever P or N position → except P or N position | Below 1 V → Pulse generation |
| D1-63 (STAR) - D1-81 (E1) | G-R - BR | Starter signal (Main) | Brake pedal depressed, shift lever P or N position, engine switch on (ST) | 11 to 14 V |
*1: Voltage is output only when the engine is cranking.
If the result is not as specified, the ECM may have a malfunction.
Using an oscilloscope, check the signal waveform of the ECM.
| Terminal No. | A7-15 (TACH) - D1-81 (E1) |
| Tool Setting | 5 V/DIV., 10 ms./DIV. |
| Vehicle Condition | Engine idling |
As the vehicle speed increases, the wavelength shortens.
CHECK STEERING LOCK ECU
Disconnect the G32 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G32-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| G32-2 (SGND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| G32-6 (IG2) - Body ground | B - Body ground | Ignition power supply | Engine switch on (IG) | 11 to 14 V |
| G32-6 (IG2) - Body ground | B - Body ground | Ignition power supply | Engine switch off | Below 1 V |
| G32-7 (B) - Body ground | B - Body ground | +B power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the G32 ECU connector.
Measure the voltage of the connector.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G32-4 (SLP1) - G32-1 (GND) | Y - W-B | Steering lock actuator position signal | Steering is locked | 11 to 14 V |
| G32-4 (SLP1) - G32-1 (GND) | Y - W-B | Steering lock actuator position signal | Steering is released | Below 1 V |
If the result is not as specified, the ECU may have a malfunction.