Home › Engine / Hybrid System › 2GR-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292073 PUSH-BUTTON START C

2GR-FE STARTING  PUSH-BUTTON START  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is output when the IG output circuits inside the main body ECU are open or shorted.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored. After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2271 LH-IG relay 1 actuation circuit or IG2 relay actuation circuit inside main body ECU is abnormal
·

Instrument panel junction block LH (Main body ECU)

·

AM2 NO. 2 fuse

·

Wire harness or connector



WIRING DIAGRAM

B167043E06
5.292,0.615 5.573,0.76 0.281,0.146 10 false G57 5.667,0.604 5.979,0.75 0.313,0.146 10 false AM1 5.667,1.24 5.99,1.385 0.323,0.146 10 false AM2 5.667,2.26 6.083,2.406 0.417,0.146 10 false GND2 5.594,3.083 6.604,3.26 1.01,0.177 10 false Main Body ECU 4.083,2.26 4.292,2.406 0.208,0.146 10 false 4A 4.219,2.792 5.354,3.115 1.135,0.323 10 false Instrument Panel Junction Block LH 4.125,2.052 4.219,2.198 0.094,0.146 10 false 3 5.469,2.167 5.563,2.313 0.094,0.146 10 false 4 5.292,1.24 5.573,1.385 0.281,0.146 10 false G58 2.479,0.781 3.198,0.927 0.719,0.146 10 false AM2 NO. 2 0.708,1.573 1.563,1.875 0.854,0.302 10 false from Battery 5.396,1.042 5.5,1.188 0.104,0.146 10 false 1 5.385,0.417 5.5,0.563 0.115,0.146 10 false 6

PROCEDURE

1.CHECK DTC OUTPUT
a.

Delete the DTCs (See page Engine / Hybrid System>2GR-FE STARTING>PUSH-BUTTON START>DTC CHECK / CLEAR).

HINT:

After all DTCs are cleared, check if the trouble occurs again 6 seconds after the engine switch is turned on (IG).



b.

Check for DTCs again.

OK:

No DTC is output.




OK

CHECK INTERMITTENT PROBLEMS

NG

2.INSPECT FUSE (AM2 NO. 2)
2.INSPECT FUSE (AM2 NO. 2)
a.

Remove the AM2 No. 2 fuse from the engine room relay block No. 1.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Disconnect the G57 and G58 main body ECU connectors.


b.

Disconnect the 4A instrument panel junction block LH connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Standard voltage:
Tester Connection Specified Condition
G57-6 (AM1) - Body ground 11 to 14 V
G58-1 (AM2) - Body ground 11 to 14 V


Standard resistance:
Tester Connection Specified Condition
4A-3 (GND2) - Body ground Below 1 Ω




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR