Home › Engine / Hybrid System › 2GR-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292073 PUSH-BUTTON START C

2GR-FE STARTING  PUSH-BUTTON START  B2289  Key Collation Waiting Time Over  


DESCRIPTION

This DTC is output when there is a LIN communication problem between the main body ECU and certification ECU or when there is a problem in the push-button start function.

HINT:

After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2289 Either condition below is met:
·

LIN communication is abnormal between the main body ECU and the certification ECU

·

The engine immobiliser system is malfunctioning


·

Instrument panel junction block LH (Main body ECU)

·

Wire harness or connector

·

Certification ECU



WIRING DIAGRAM

B137989E15
0.57,3.214 1.684,3.375 1.114,0.161 10 Certification ECU 0.577,3.077 0.862,3.219 0.286,0.142 10 G29 4.079,1.993 4.272,2.135 0.193,0.142 10 4A 1.301,1.998 1.549,2.140 0.248,0.142 10 LIN 5.648,1.993 5.962,2.135 0.314,0.142 10 LIN1 5.597,3.095 6.614,3.251 1.017,0.156 10 Main Body ECU 4.22,2.517 5.356,2.842 1.136,0.325 10 Instrument Panel Junction Block LH 5.414,2.082 5.593,2.233 0.179,0.152 10 14 1.603,2.082 1.782,2.233 0.179,0.152 10 10 4.093,1.781 4.291,1.933 0.198,0.152 10 20

PROCEDURE

1.CHECK FOR DTCS

b.

Check for DTC B2289 (Key collection waiting time over) and B2785 (Communication malfunction between ECUs connected by LIN).

Result:
Display (DTC output) Proceed to
"DTC B2289" only A
"DTC B2785" only B
No DTC C


HINT:
·

If DTC B2785 is output, perform troubleshooting for DTC B2785 first (See page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>B2785).





A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)

B

C

CHECK INTERMITTENT PROBLEMS

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)
a.

Disconnect the G29 and 4A ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
4A-20 (LIN1) - G29-10 (LIN) Always Below 1 Ω
4A-20 (LIN1) or G29-10 (LIN) - Body ground Always 10 kΩ or higher




OK

3.CHECK MAIN BODY ECU OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU OPERATION
a.

After replacing the main body ECU with a normally functioning ECU, check that the engine starts.

OK:

Engine starts normally.


HINT:

If the engine does not start, refer to "Room Oscillator does not Recognize Key" (See page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>Room Oscillator does not Recognize Key).




OK

END (MAIN BODY ECU DEFECTIVE)

NG

GO TO OTHER PROBLEM (Engine does not Start)