Home › Engine / Hybrid System › 2GR-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292073 PUSH-BUTTON START J

2GR-FE STARTING  PUSH-BUTTON START  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

When the engine switch is pushed with the electrical key in the cabin, the main body ECU receives signals to switch the power source mode.

HINT:
·

To allow use of the GTS to inspect the push-button start function when the engine switch is off, repeat opening and closing any of the doors. Opening and closing a door establishes communication between the GTS and the main body ECU. (Opening and closing a door can also be simulated by operating a door courtesy light switch.)

·

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored. After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.



WIRING DIAGRAM

B167169E02
5.239,1.021 5.430,1.170 0.191,0.149 10 5A 5.287,0.799 5.383,0.948 0.096,0.149 10 1 5.235,1.467 5.433,1.616 0.198,0.149 10 5D 6.216,1.588 6.710,1.934 0.494,0.346 10 to Each System 5.245,1.25 5.417,1.399 0.172,0.149 10 14 5.232,1.922 5.436,2.071 0.205,0.149 10 5G 5.247,1.726 5.422,1.875 0.176,0.149 10 14 5.232,2.379 5.436,2.528 0.205,0.149 10 5G 5.248,2.165 5.420,2.314 0.172,0.149 10 15 5.246,2.819 5.423,2.968 0.177,0.149 10 5L 5.287,2.623 5.383,2.772 0.096,0.149 10 6 5.787,3.743 6.080,3.892 0.293,0.149 10 G57 5.932,5.343 6.114,5.492 0.182,0.149 10 15 6.17,5.446 6.352,5.595 0.182,0.149 10 IG 6.17,3.746 6.518,3.895 0.349,0.149 10 IG1D 5.885,3.561 5.981,3.710 0.096,0.149 10 3 5.239,0.565 5.430,0.714 0.191,0.149 10 5K 4.303,0.692 4.806,0.841 0.503,0.149 10 FR WIP 2.572,0.692 3.520,0.841 0.948,0.149 10 SEAT HTR RH 0.046,0.556 1.411,0.698 1.365,0.142 10 to Seat Heater Switch 0.62,1.612 1.448,1.754 0.828,0.142 10 RH-MAIN-JB 1.339,4.671 2.167,4.812 0.828,0.142 10 LH-MAIN-JB 3.497,5.096 4.418,5.237 0.921,0.142 10 SEAT HTR LH 3.497,5.563 4.418,5.704 0.921,0.142 10 GAUGE NO. 2 1.592,6.249 2.096,6.581 0.504,0.332 10 to Each System 0.363,6.539 0.636,6.685 0.272,0.147 10 ALT 0.228,8.533 0.343,8.679 0.115,0.147 10 A 0.798,8.533 0.913,8.679 0.115,0.147 10 B 1.125,8.533 1.249,8.679 0.124,0.147 10 C 3.595,6.926 4.321,7.068 0.726,0.142 10 LH ECU-IG 4.725,7.58 5.627,7.722 0.902,0.142 10 LH IG Relay 1 3.072,8.21 6.419,8.352 3.347,0.142 10 Instrument Panel Junction Block LH (Main Body ECU) 2.846,2.247 3.793,2.396 0.948,0.149 10 RH-IG Relay 1 2.614,3.241 4.867,3.390 2.253,0.149 10 Instrument Panel Junction Block RH 4.057,1.585 4.804,1.734 0.746,0.149 10 RH ECU-IG 5.287,0.355 5.383,0.504 0.096,0.149 10 9 2.045,1.46 2.260,1.609 0.215,0.149 10 5M 2.105,1.25 2.201,1.399 0.096,0.149 10 1 2.052,1.922 2.253,2.071 0.201,0.149 10 5D 2.066,1.726 2.238,1.875 0.172,0.149 10 12 2.052,2.375 2.253,2.524 0.201,0.149 10 5D 2.105,2.165 2.201,2.314 0.096,0.149 10 7 2.057,2.833 2.248,2.982 0.191,0.149 10 5A 2.105,2.623 2.201,2.772 0.096,0.149 10 4 2.052,0.551 2.253,0.700 0.201,0.149 10 5D 2.066,0.355 2.238,0.504 0.172,0.149 10 13 2.776,4.989 2.969,5.138 0.193,0.149 10 4A 2.786,4.792 2.960,4.941 0.174,0.149 10 12 2.786,5.413 2.960,5.562 0.174,0.149 10 4L 2.825,5.217 2.921,5.366 0.096,0.149 10 9 2.776,5.889 2.969,6.038 0.193,0.149 10 4A 2.786,5.693 2.960,5.842 0.174,0.149 10 13 2.767,6.328 2.978,6.477 0.211,0.149 10 4G 2.783,6.132 2.962,6.281 0.179,0.149 10 11 2.825,7.489 2.921,7.638 0.096,0.149 10 6 2.769,6.786 2.976,6.935 0.207,0.149 10 4G 2.769,7.243 2.976,7.392 0.207,0.149 10 4G 2.787,7.047 2.959,7.196 0.172,0.149 10 10 2.776,7.686 2.969,7.835 0.193,0.149 10 4K 2.786,6.59 2.960,6.739 0.174,0.149 10 12 2.767,4.519 2.978,4.668 0.211,0.149 10 4M 2.825,4.323 2.921,4.471 0.096,0.149 10 1

B168634E02
3.355,1.898 5.580,2.058 2.225,0.159 10 Instrument Panel Junction Block LH 2.785,1.48 2.975,1.629 0.191,0.149 10 4A 2.651,2.629 3.296,2.778 0.644,0.149 10 F/B BATT 4.456,2.629 5.178,2.804 0.722,0.175 10 AM2 NO. 2 2.329,3.189 2.659,3.338 0.330,0.149 10 MET 1.278,3.224 1.775,3.547 0.497,0.323 10 to Each System 0.461,4.717 0.937,4.897 0.476,0.180 10 Battery 0.382,3.429 0.792,3.770 0.410,0.341 10 FL MAIN 2.357,3.666 2.632,3.815 0.275,0.149 10 IGN 4.349,3.059 4.600,3.208 0.251,0.149 10 IG2 3.492,4.328 3.738,4.477 0.246,0.149 10 IG2 4.003,3.909 4.111,4.058 0.107,0.149 10 1 4.003,3.448 4.104,3.597 0.100,0.149 10 5 3.128,3.909 3.235,4.058 0.107,0.149 10 2 3.128,3.448 3.228,3.597 0.100,0.149 10 3 6.187,2.486 6.494,2.635 0.306,0.149 10 AM1 5.787,2.486 6.074,2.635 0.288,0.149 10 G57 5.871,2.271 5.969,2.420 0.098,0.149 10 6 5.991,1.388 6.089,1.537 0.098,0.149 10 4 6.187,3.266 6.494,3.414 0.306,0.149 10 AM2 5.787,3.271 6.074,3.420 0.288,0.149 10 G58 5.871,3.051 5.969,3.200 0.098,0.149 10 1 6.187,3.989 6.535,4.138 0.348,0.149 10 IG2D 5.787,3.996 6.074,4.145 0.288,0.149 10 G58 5.843,3.787 6.015,3.936 0.172,0.149 10 11 6.187,4.685 6.596,4.834 0.408,0.149 10 GND1 6.187,1.464 6.631,1.650 0.444,0.185 10 GND2 6.044,5.112 7.057,5.261 1.012,0.149 10 Main Body ECU 5.787,4.682 6.074,4.831 0.288,0.149 10 G59 5.871,4.47 5.969,4.619 0.098,0.149 10 1 2.834,1.27 2.938,1.419 0.104,0.149 10 3 2.785,1.021 2.982,1.170 0.198,0.149 10 4D 2.799,0.811 2.973,0.960 0.173,0.149 10 11 2.785,0.567 2.982,0.716 0.198,0.149 10 4A 2.838,0.349 2.935,0.498 0.097,0.149 10 5 0.232,0.18 0.347,0.329 0.115,0.149 10 A 0.802,0.18 0.917,0.329 0.115,0.149 10 B 1.138,0.18 1.258,0.329 0.120,0.149 10 C

PROCEDURE

1.INSPECT FUSE (AM2 NO. 2 AND F/B BATT)
a.

Remove the AM2 No. 2 and F/B BATT fuses from the engine room junction block No. 1.


b.

Remove the SEAT HTR LH, GAUGE NO. 2 and LH ECU-IG fuses from the instrument panel junction block LH.


c.

Remove the SEAT HTR RH, RH ECU-IG and FR WIP fuses from the instrument panel junction block RH.


d.

Measure the resistance of the fuses.

HINT:

When the fuse is shorted, check the system which is supplied the power through the shorted fuse, before replace it.


Standard resistance:

Below 1 Ω




OK

2.CHECK CONNECTORS

NG

REPLACE FUSE

2.CHECK CONNECTORS
a.

Check that the connectors are securely connected and the terminals are not deformed or loose.

OK:

The connectors are securely connected and the terminals are not deformed or loose.




OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)

NG

REPAIR OR REPLACE CONNECTORS

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
a.

Disconnect the G57 and G58 ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G57-6 (AM1) - Body ground Always 11 to 14 V
G58-1 (AM2) - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)
a.

Disconnect the G59 main body ECU connectors.


b.

Disconnect the 4A instrument panel junction block LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G59-1 (GND1) - Body ground Always Below 1 Ω
4A-3 (GND2) - Body ground Always Below 1 Ω
4A-5 - Body ground Always Below 1 Ω




OK

5.INSPECT RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RELAY (IG2 RELAY)
a.
B426341E05
2.625,0.75 2.927,0.5 false 2.469,1.135 2.896,0.969 false 2.469,1.625 2.906,1.458 false 2.031,0.708 1.719,0.469 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 1 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.323 1.396,1.542 0.219,0.219 10 false 2 1.563,0.354 1.781,0.573 0.219,0.219 10 false 1 2.99,0.875 3.208,1.094 0.219,0.219 10 false 5 2.979,1.375 3.198,1.594 0.219,0.219 10 false 3 2.969,0.417 3.188,0.635 0.219,0.219 10 false 2

Remove the IG2 relay from the engine room relay block No. 1.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE IG2 RELAY

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU AND BODY GROUND)
a.

Remove the IG2 relay from the engine room relay block No. 1.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Engine room relay block IG2 relay terminal 1 - G58-11 (IG2D) Always Below 1 Ω
Engine room relay block IG2 relay terminal 2 - Body ground Below 1 Ω
G58-11 (IG2D) - Body ground 10 kΩ or higher




OK

7.INSPECT MAIN BODY ECU (IG2D VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT MAIN BODY ECU (IG2D VOLTAGE)
a.

Reconnect the G58 connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G58-11 (IG2D) - Body ground Engine switch on (IG) Output voltage at terminal AM1 or AM2 is -2 V or more.


HINT:
·

Terminal AM1: G57-6

·

Terminal AM2: G58-1





OK

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.

Disconnect the 5A and 5D instrument panel junction block RH connectors.


b.

Disconnect the 4D instrument panel junction block LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G57-3 (IG1D) - 5D-7 Always Below 1 Ω
G57-3 (IG1D) or 5D-7 - Body ground Always 10 kΩ or higher
5D-12 - 4D-11 Always Below 1 Ω
5D-12 or 4D-11 - Body ground Always 10 kΩ or higher
5A-4 - Body ground Always Below 1 Ω




OK

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK RH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK RH - BATTERY)
a.

Disconnect the 5M connector from instrument panel junction block RH.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester connection Condition Specified Condition
5M-1 - Body ground Always 11 to 14 V




OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH (INNER CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK RH (INNER CIRCUIT)
a.

Disconnect the 5G, 5K, 5L and 5M instrument panel junction block RH connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
5D-7 - 5D-12 Always Below 1 Ω
5D-7 - 5A-4 Always Below 1 Ω
5M-1 - 5A-1 When battery voltage is applied to 5D-7 - 5A-4 Below 1 Ω
5M-1 - 5D-13
5M-1 - 5D-14
5M-1 - 5G-14
5M-1 - 5G-15
5M-1 - 5K-9
5M-1 - 5L-6
5M-1 - 5A-1 When battery voltage is not applied to 5D-7 - 5A-4 10 kΩ or higher
5M-1 -5D-13
5M-1 - 5D-14
5M-1 - 5G-14
5M-1 - 5G-15
5M-1 - 5K-9
5M-1 - 5L-6




OK

11.CHECK HARNESS AND CONNECTOR

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH

11.CHECK HARNESS AND CONNECTOR
a.

Disconnect the 4M instrument panel junction block LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester connection Condition Specified condition
4M-1 - Body ground Always 11 to 14 V




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR