Home › Engine / Hybrid System › 2GR-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292073 PUSH-BUTTON START C

2GR-FE STARTING  PUSH-BUTTON START  B2285  Steering Lock Position Signal Circuit Malfunction  


DESCRIPTION

This DTC is output when serial communication signals and LIN communication signals in the circuit between the main body ECU and steering lock actuator (steering lock ECU) are inconsistent.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

After the main body ECU or steering lock ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2285 Cable and LIN information between the main body ECU and the steering lock ECU are inconsistent
·

Instrument panel junction block LH (Main body ECU)

·

Steering lock ECU

·

Wire harness or connector



WIRING DIAGRAM

B157547E05
0.877,0.956 1.250,1.115 0.373,0.159 10 SLP1 0.993,2.553 1.251,2.712 0.258,0.159 10 LIN 2.522,2.553 3.094,2.712 0.572,0.159 10 LIN Line 1.344,0.854 1.465,1.005 0.120,0.151 10 4 1.344,2.386 1.465,2.537 0.120,0.151 10 5 4.407,2.334 4.583,2.492 0.176,0.159 10 20 4.401,2.548 4.596,2.703 0.195,0.155 10 4A 4.478,3.05 5.665,3.410 1.186,0.361 10 Instrument Panel Junction Block LH 5.7,2.436 5.874,2.591 0.174,0.155 10 14 5.978,2.548 6.309,2.703 0.331,0.155 10 LIN1 5.978,0.962 6.309,1.117 0.331,0.155 10 SLP 5.623,0.762 5.828,0.916 0.204,0.155 10 18 5.884,4.18 6.915,4.323 1.031,0.143 10 Main Body ECU 0.235,4.167 0.517,4.321 0.282,0.154 10 G32 0.235,4.323 1.457,4.477 1.222,0.154 10 Steering Lock ECU 5.571,0.958 5.854,1.129 0.283,0.172 10 G57

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Check the DATA LIST for proper functioning of the steering lock function.

HINT:

When using the GTS with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.


Main Body ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Unlock Switch Steering lock condition / ON or OFF ON: Steering is unlocked (Engine switch on (ACC))
OFF: Steering is locked (Engine switch off)
-

OK:

ON (steering is unlocked) and OFF (steering is locked) appear on the screen.




OK

2.CHECK FOR DTCS

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STEERING LOCK ECU)
2.CHECK FOR DTCS

b.

Check for DTC B2285 (Steering lock position signal circuit malfunction), DTC B2287 (LIN communication master malfunction) and DTC B2785 (Communication malfunction between ECUs connected by LIN).

Result:
Display (DTC output) Proceed to
"DTC B2285" only A
"DTC B2287" and/or "DTC B2785" B
No DTC C


HINT:




A

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

B

GO TO DTC CHART

C

CHECK INTERMITTENT PROBLEMS

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STEERING LOCK ECU)
a.

Disconnect the G57, 4A and G32 ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G57-18 (SLP) - G32-4 (SLP1) Always Below 1 Ω
4A-20 (LIN1) - G32-5 (LIN) Always Below 1 Ω
G57-18 (SLP) or G32-4 (SLP1) - Body ground Always 10 kΩ or higher
4A-20 (LIN1) or G32-5 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK MAIN BODY ECU OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MAIN BODY ECU OPERATION
a.

After replacing the main body ECU with a normally functioning ECU, check that the engine starts. Make sure the brake pedal is depressed and the shift position is P at this time.


b.

Check that the engine switch mode can be changed by pushing the engine switch.

HINT:

Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.


OK:

Engine starts normally.




OK

END (MAIN BODY ECU DEFECTIVE)

NG

REPLACE STEERING LOCK ECU