Home › Engine / Hybrid System › 2AZ-FE STARTING › STARTER(for 1.7 kW Type)
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292079 STARTER(for 1.7 kW Type) G

2AZ-FE STARTING  STARTER(for 1.7 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

NOTICE:

These tests must be performed within 3 to 5 seconds to avoid burning out the coil.


a.

Perform the pull-in test.

i.

Disconnect the lead wire from terminal C.


ii.
A060459E09
2.021,0.073 2.781,0.24 0.76,0.167 10 false Terminal C 0.552,1.854 1.375,2.01 0.823,0.156 10 true Terminal 50

Connect the battery to the magnetic switch as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not move, replace the magnetic switch.



b.
A081044E24
1.385,1.323 2.219,0.479 2.219,0.479 2.292,0.479 false 1.5,0.073 2.26,0.271 0.76,0.198 10 false Disconnect 2.292,0.385 3.031,0.573 0.74,0.188 10 false Terminal C

Perform the hold-in test.

i.

Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.

If the clutch pinion gear returns inward, replace the magnetic switch.



c.
A081045E18
1.635,0.25 2.438,0.417 0.802,0.167 10 false Disconnect

Perform the clutch pinion gear return test.

i.

Disconnect the negative (-) lead from the switch body. Check that the clutch pinion gear returns.

If the clutch pinion gear does not return, replace the magnetic switch.



d.
A060462E19
0.969,1.875 1.729,2.042 0.76,0.167 10 true Terminal 50 0.344,1.552 1.104,1.719 0.76,0.167 10 false Terminal 30

Perform the no-load performance test.

i.

Connect the lead wire to terminal C. Make sure that the lead is not grounded.


ii.

Clamp the starter in a vise.


iii.

Connect the battery and an ammeter to the starter as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28226B 2.INSPECT MAGNETIC SWITCH ASSEMBLY

a.
A058586

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the magnetic switch assembly.



b.
A079725E41
2.219,0.927 2.219,0.354 2.219,0.354 2.333,0.354 false 1.76,1.604 1.188,1.604 false 2.333,0.271 3.104,0.469 0.771,0.198 10 false Terminal C 2.479,1.531 3.229,1.708 0.75,0.177 10 false Below 1 Ω 0.26,1.521 1.021,1.698 0.76,0.177 10 false Terminal 50

Check if the pull-in coil has an open circuit.

i.

Measure the resistance between terminals 50 and C.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the magnetic switch assembly.



c.
A079726E01
1.896,1.604 1.421,1.604 false 0.498,1.518 1.283,1.710 0.785,0.192 10 Terminal 50 2.223,0.258 2.998,0.448 0.775,0.191 10 Below 2 Ω 1.295,0 1.716,0.205 0.421,0.205 10 Body

Check if the hold-in coil has an open circuit.

i.

Measure the resistance between terminal 50 and the switch body.

Standard resistance:

Below 2 Ω


If the result is not as specified, replace the magnetic switch assembly.



Hide 28160 3.INSPECT STARTER ARMATURE ASSEMBLY

a.
A058372E34
1.448,1.156 2.594,1.25 2.594,1.25 1.354,1.25 false 0.573,0.021 1.521,0.25 0.948,0.229 10 false Below 1 Ω 2.594,1.177 3.229,1.375 0.635,0.198 10 false Segment

Check if the commutator has an open circuit.

i.

Check the resistance between the segments of the commutator.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the armature assembly.



b.
A058373E31
1.333,1.177 1.052,1.281 false 1.854,1.042 2.531,1.5 false 0.167,1.177 1.083,1.375 0.917,0.198 10 false Commutator 2.563,1.427 3.208,1.646 0.646,0.219 10 false Coil Core 0.281,0.063 1.385,0.396 1.104,0.333 10 true 10 kΩ or Higher

Check if the commutator is grounded.

i.

Measure the resistance between the commutator and armature coil core.

Standard resistance:

10 kΩ or higher


If the result is not as specified, replace the armature assembly.



c.

Check the commutator for contamination and burns on its surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.


d.
A058584E01
2.788,0.823 3.230,1.024 0.442,0.201 10 Length

Using a vernier caliper, measure the commutator's length.

Standard length:

3.1 to 3.8 mm (0.122 to 0.150 in.)


If the length is greater than the maximum, replace the starter armature assembly.


Hide 28130 4.INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A076677E01
2.715,1.094 3.157,1.295 0.442,0.201 10 Length

Using a vernier caliper, measure the brush length.

Standard length:

4.0 to 9.0 mm (0.158 to 0.359 in.)


If the length is less than the minimum, replace the end frame assembly.


b.
A079766E23
1.125,0.219 2.198,0.406 1.073,0.188 10 false 10 kΩ or Higher

Check the brush insulation.

i.

Measure the resistance between the positive (+) and negative (-) brush.

Standard resistance:

10 kΩ or higher


If the result is not as specified, repair or replace the end frame assembly.



Hide 5.INSPECT STARTER CLUTCH

a.
A081655E26
1.583,0.031 1.948,0.219 0.365,0.188 10 false Lock 1.49,1.604 1.854,1.792 0.365,0.188 10 false Free

Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.

If necessary, replace the starter drive housing assembly.