Home › Engine / Hybrid System › 2AZ-FE STARTING › STARTER(for 1.7 kW Type)
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292079 STARTER(for 1.7 kW Type) A

2AZ-FE STARTING  STARTER(for 1.7 kW Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Use high-temperature grease to lubricate the bearings, gears, return spring and steel ball when assembling the starter.


PROCEDURE

Hide 28255 1.INSTALL PLANETARY GEAR

a.
A081656E22
1.677,1.125 2.406,0.552 2.406,0.552 2.271,1.344 false 2.406,0.552 1.823,1.135 false 2.104,0.135 3,0.302 0.896,0.167 10 false Apply Grease

Apply grease to the planetary gears and pin parts of the planetary shaft.


b.

Install the 3 planetary gears.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.
A082440E32
1.354,0.552 1.552,0.552 false 0.031,0.458 1.125,0.635 1.094,0.177 10 false Snap Ring Pliers

Apply grease to the plate washer and the armature shaft.


b.

Install the starter armature to the starter commutator end frame.


c.

Using snap ring pliers, install the plate washer and a new snap ring.


d.
A058810E01
1.374,0.157 1.816,0.358 0.442,0.201 10 Length

Using a vernier caliper, measure the length of the snap ring.

Maximum length:

5.0 mm (0.197 in.)


If the length is greater than the maximum, replace it with a new snap ring.


Hide 28132A 3.INSTALL STARTER COMMUTATOR END FRAME COVER

a.
A081178

Install the end frame cover to the commutator end frame.


Hide 28177 4.INSTALL STARTER ARMATURE PLATE

a.
A073991E04
1.126,0.256 1.427,0.430 0.302,0.174 10 Key 0.172,0.245 0.705,0.396 0.533,0.151 10 Keyway 1.85,0.843 1.507,0.356 false 0.136,0.328 0.016,0.328 0.016,0.328 0.339,1.153 false

Insert the armature plate to the starter yoke.


b.

Align the keyway of the starter plate with the key inside the starter yoke, and install the starter plate.


Hide 28130 5.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A079727E01
0.339,0.464 0.805,0.629 0.466,0.165 10 Cutout 0.711,0.085 1.214,0.257 0.503,0.172 10 Rubber 2.011,0.517 1.721,0.195 1.721,0.195 1.33,0.195 false 1.576,0.762 1.057,0.543 1.057,0.543 0.895,0.543 false

Align the rubber of the end frame with the cutout of the starter yoke.


b.

Install the end frame to the starter yoke.


Hide 28120 6.INSTALL STARTER YOKE ASSEMBLY

a.
A079728E24
1.563,1.219 1.896,1.365 false 1.344,1.198 1.26,1.74 false 1.01,1.76 1.615,1.958 0.604,0.198 10 false Cutout 1.927,1.292 2.615,1.49 0.688,0.198 10 false Protrusion

Align the protrusion of the starter yoke with the cutout of the starter drive housing.


b.
A079720

Install the starter yoke with the 2 through-bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28226B 7.INSTALL MAGNETIC SWITCH ASSEMBLY

a.
A079729

Apply grease to the plunger and the hook.


b.

Hang the plunger hook of the magnetic switch to the drive lever.


c.

Install the plunger and return spring.


d.
A079719

Install the magnetic switch with the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.
A079718

Connect the lead wire to the magnetic switch with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)