Home › Engine / Hybrid System › 2AZ-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292080 SMART ENTRY AND START SYSTEM U

2AZ-FE STARTING  SMART ENTRY AND START SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU


U188401E02
5.76,3.885 5.896,2.365 false 5.948,2.198 7.021,2.5 1.073,0.302 10 false Main Body ECU 2.49,2.146 4.813,2.323 2.323,0.177 10 false Instrument Panel Junction Block LH 2.698,4.135 3.26,4.479 0.563,0.344 10 false 4A 4.302,5.469 4.865,5.813 0.563,0.344 10 false 4K 6.406,4.24 6.969,4.583 0.563,0.344 10 false G57 6.406,4.99 6.969,5.333 0.563,0.344 10 false G58 6.406,5.625 6.969,5.969 0.563,0.344 10 false G59 6.406,6.094 6.969,6.438 0.563,0.344 10 false G60

a.

Disconnect the G57, G58 and G59 main body ECU connectors.


b.

Disconnect the 4K and 4A instrument panel junction block LH connectors.


c.

Measure the voltage and resistance of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
BATB (4K-9) - Body ground B - Body ground +B power supply Always 10 to 14 V
AM1 (G57-6) - Body ground SB - Body ground +B power supply Always 10 to 14 V
AM2 (G58-1) - Body ground SB - Body ground +B power supply Always 10 to 14 V
SSW1 (G57-17) - Body ground P - Body ground Engine switch 1 input Engine switch pushed Below 1 Ω
SSW1 (G57-17) - Body ground P - Body ground Engine switch 1 input Engine switch not pushed 10 kΩ or higher
SSW2 (G57-16) - Body ground G - Body ground Engine switch 2 input Engine switch pushed Below 1 Ω
SSW2 (G57-16) - Body ground G - Body ground Engine switch 2 input Engine switch not pushed 10 kΩ or higher
GND1 (G59-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
GND2 (4A-3) - Body ground W-B - Body ground Ground Always Below 1 Ω
LIN1 (4A-20) - Body ground R - Body ground LIN line Always 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.



d.

Reconnect the G57, G58 and G59 main body ECU connectors.


e.

Reconnect the 4K and 4A instrument panel junction block LH connectors.


f.

Measure the voltages of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
ACCD (G57-22) - GND2 (4A-3) GR - W-B ACC relay drive signal Ignition switch on (ACC) 10 to 14 V
ACCD (G57-22) - GND2 (4A-3) GR - W-B ACC relay drive signal Ignition switch off Below 1 V
IG2D (G58-11) - GND2 (4A-3) G - W-B IG2 relay drive signal Ignition switch on (IG) 10 to 14 V
IG2D (G58-11) - GND2 (4A-3) G - W-B IG2 relay drive signal Ignition switch on (ACC) Below 1 V
SLR+ (G57-19) - GND2 (4A-3) L - W-B Steering lock power supply Steering lock motor operating Below 1 V
SLR+ (G57-19) - GND2 (4A-3) L - W-B Steering lock power supply Steering lock motor not operating 10 to 14 V
SLP (G57-18) - GND2 (4A-3) Y - W-B Steering lock actuator position signal Steering lock locked 10 to 14 V
SLP (G57-18) - GND2 (4A-3) Y - W-B Steering lock actuator position signal Steering lock released Below 1 V
SPD (G59-9) - GND2 (4A-3) W - W-B Speed signal from combination meter Ignition switch on (IG), Rotate driving wheel slowly Pulse generation
(see waveform 1)
TACH (G59-8) - GND2 (4A-3) R - W-B Tachometer signal Engine running Pulse generation
(see waveform 2)
STSW (G60-4) - GND2 (4A-3) P - W-B Starter activation request signal Brake pedal depressed with shift lever in P or N, ignition switch pushed once 10 to 14 V*
STR (G57-8) - GND2 (4A-3) G - W-B Park / neutral position switch Shift lever in P or N Below 1 V
STR2 (G60-6) - GND2 (4A-3) SB - W-B Starter signal Brake pedal depressed with shift lever in P or N, ignition switch pushed once 10 to 14 V*
INDS (G57-15) - GND2 (4A-3) Y - W-B Vehicle condition signal Brake pedal depressed with shift lever in P or N, ignition switch off, on (ACC, IG) 9 to 14 V
INDW (G57-14) - GND2 (4A-3) GR - W-B Vehicle condition signal Brake pedal released with shift lever in P or N, ignition switch off, on (ACC, IG) 9 to 14 V
SWIL (G57-25) - GND2 (4A-3) SB- W-B Illumination signal Light control switch TAIL or HEAD 10 to 14 V
STP (4K-7) - GND2 (4A-3) L- W-B Stop light switch signal Brake pedal depressed 10 to 14 V

HINT:

*: Voltage is output for 0.3 seconds before the engine is started.


If the result is not as specified, the ECU may have a malfunction.


g.
I042329E28
2.844,1.24 3.25,1.438 0.406,0.198 10 false GND 0.104,0.021 1,0.177 0.896,0.156 10 false Waveform 1:

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Symbols (Terminal No.) SPD (G59-9) - GND2 (4A-3)
Tool setting 5 V/DIV., 10 msec./DIV
Condition Driving at approx. 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the wavelength shortens.



h.
I042330E32
2.896,1.25 3.333,1.448 0.438,0.198 10 false GND 0.094,0 1.052,0.167 0.958,0.167 10 false Waveform 2:

Using an oscilloscope, check waveform 2.

Waveform 1 (Reference)
Item Content
Symbols (Terminal No.) TACH (G59-8) - GND2 (4A-3)
Tool setting 5 V/DIV., 10 msec./DIV
Condition Engine idling

HINT:

As the vehicle speed increases, the wavelength shortens.




CHECK CERTIFICATION ECU


U188567E02
3.49,0.302 3.771,0.479 0.281,0.177 10 false G29

a.

Disconnect the G29 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
+B1 (G29-1) - Body ground R - Body ground +B power supply Always 10 to 14 V
IG (G29-18) - Body ground R - Body ground Ignition power supply Ignition switch on (IG) 10 to 14 V
IG (G29-18) - Body ground R - Body ground Ignition power supply Ignition switch off Below 1 V
LIN (G29-10) - Body ground GR - Body ground LIN line Always 10 kΩ or higher
E (G29-17) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.




CHECK ECM


U188990E02
5.094,0.406 5.292,0.552 0.198,0.146 10 false A7 2.646,0.396 2.854,0.542 0.208,0.146 10 false D2

a.

Disconnect the A7 and D2 ECM connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
BATT (A7-20) - E1 (D2-104) W - BR Battery (for measuring battery voltage and for ECM memory) Always 10 to 14 V
+B (A7-2) - E1 (D2-104) B - BR Power source of ECM Ignition switch on (IG) 10 to 14 V
+B2 (A7-1) - E1 (D2-104) B - BR Power source of ECM Ignition switch off 10 to 14 V
IGSW (A7-28) - E1 (D2-104) BE - BR Ignition switch signal Always 10 to 14 V
E1 (D2-104) - Body ground BR - Body ground Ground Always Below 1 Ω
E02 (D2-44) - Body ground BR - Body ground Ground Always Below 1 Ω
E04 (D2-46) - Body ground BR - Body ground Ground Always Below 1 Ω
E01 (D2-45) - Body ground BR - Body ground Ground Always Below 1 Ω
E03 (D2-86) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the A7 and D2 ECM connectors.


d.

Measure the voltage of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
STA (A7-48) - E1 (D2-104) B - BR Starter relay operation signal Cranking 5.5 V or more
ACCR (A7-13) - E1 (D2-104) GR - BR ACC relay cut signal
(output)
Ignition switch on (IG) → Cranking 10 to 14 V → Below 1 V
TACH (A7-15) - E1 (D2-104) B - BR Engine revolution signal
(output)
Idling Pulse generation
(see waveform 1)
STAR (D2-52) - E1 (D2-104) G - BR*1
LG - BR*2
Starter relay drive signal Cranking 10 to 14 V

*1: A/T

*2: CVT


If the result is not as specified, the ECM may have a malfunction.



e.
I042330E33
2.896,1.24 3.333,1.438 0.438,0.198 10 false GND 0.063,0 1.135,0.156 1.073,0.156 10 false Waveform 1:

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Symbols (Terminal No.) TACH (A7-15) - E1 (D2-104)
Tool setting 5 V/DIV., 10 msec./DIV
Condition Engine idling

HINT:

As the vehicle speed increases, the wavelength shortens.




CHECK STEERING LOCK ECU


U188552E02
3.438,0.271 3.75,0.469 0.313,0.198 10 false G32

a.

Disconnect the G32 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (G32-7) - Body ground B - Body ground +B power supply Always Always
IG2 (G32-6) - Body ground B - Body ground Ignition power supply Ignition switch on (IG) Always
IG2 (G32-6) - Body ground B - Body ground Ignition power supply Ignition switch off Below 1 V
GND (G32-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
SGND (G32-2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.