PUSH-BUTTON START DESCRIPTION
The push-button start uses a push-type ignition switch, which the driver can operate by merely carrying the key. This system consists primarily of the main body ECU, engine switch, ID code box, steering lock ECU, key, ACC relay, LH-IG relay 1, IG2 relay and certification ECU. The main body ECU controls the system. This function operates in cooperation with the smart entry and start system. The table below shows the transition of the engine switch, which depends on whether the brake pedal is depressed or released.
This system has different power source mode patterns depending on the brake pedal and shift lever conditions.
| Condition | Power Source Mode Pattern |
|---|---|
| Brake pedal not depressed, shift lever in P | Each time ignition switch is pushed
·
off → on (ACC) → on (IG) → off |
| Brake pedal not depressed | When ignition switch is pushed in engine started condition
·
Engine started → off |
| Brake pedal depressed, shift lever in P or N | When ignition switch is pushed once
·
off → engine start |
| Brake pedal depressed, shift lever in P or N | When ignition switch is pushed in on (ACC) condition
·
on (ACC) → engine start |
| Brake pedal depressed, shift lever in P or N | When ignition switch is pushed in on (IG) condition
·
on (IG) → engine start |
| Brake pedal depressed | When ignition switch is pushed in engine started condition
·
Engine started → off |
When the battery of the key is low, the push-button start function can be operated by holding the key against the engine switch.
FUNCTION OF COMPONENT
| Components | Function |
|---|---|
| Engine Switch
(Transponder Key Amplifier) |
·
Transmits engine switch signal to main body ECU. ·
Informs driver of power source mode or system abnormality with indicator light illumination. ·
Receives ID code and transmits it to certification ECU when battery of key is low. |
| Key | ·
Receives signals from oscillators and returns ID code to entry door control receiver. |
| Indoor Electrical Key Oscillator | ·
Receives request signal from certification ECU and forms detection area in vehicle interior. |
| Door Control Receiver | ·
Receives ID code from key and transmits it to certification ECU. |
| Main Body ECU | ·
Changes power source mode in 4 stages (off, on (ACC), on (IG), start) in accordance with state of park / neutral position switch. ·
Controls push-button start function in accordance with signals received from switches and each ECU. |
| Certification ECU | ·
Certifies ID code received from entry door control receiver and transmits certification results to ID code box and steering lock ECU. |
| Park / Neutral Position Switch | ·
Outputs state of shift position to main body ECU. |
| Stop Light Switch | ·
Outputs state of brake pedal to main body ECU. |
| ID Code Box | ·
Receives steering unlock or engine immobiliser unset signals from certification ECU, certifies them, and transmits each unset signal to steering lock ECU or ECM. |
| ECM | ·
Receives engine start request signal from power source control ECU, turns ON ST relay, and starts engine. ·
Receives signal from ID code box and performs engine ignition and fuel injection. |
SYSTEM FUNCTION
The electric controls of the push-button start function are described below:
| Control | Outline |
|---|---|
| Engine Switch Control | ·
When driver operates engine switch with key in driver's possession, certification ECU starts indoor electrical key oscillator, which transmits request signal to key. Upon receiving this signal, key transmits ID code signal to main body ECU. ·
ID code box verifies check results received from certification ECU via LIN line and sends them to main body ECU. Based on these results, main body ECU authorizes operation of engine switch. |
| Diagnosis | ·
When main body ECU detects malfunction, main body ECU diagnoses and memorizes failed section. |
CONSTRUCTION AND OPERATION
Engine switch:
The engine switch consists of a momentary type switch, 3 color (amber, green, greenish white) LEDs, and transponder key amplifier.
The greenish white LED is for illumination.
The amber and green LEDs are for the indicator lights. The driver can check the present power source mode and whether the engine can start or not in accordance with the illumination state of the indicator light.
When the main body ECU detects an abnormality in the smart entry and start system, it makes the amber indicator light flash. If the engine is stopped in this state, it might not be possible to restart it.
Indicator light condition:
| Power Source Mode/Condition | Indicator Light Condition | |
| Brake pedal released | Brake pedal depressed, shift lever in P or N | |
| Off | OFF | Illuminates (green) |
| On (ACC, IG) | Illuminates (amber) | Illuminates (green) |
| Engine running | OFF | OFF |
| Steering lock locked | Flashes (green) for 30 seconds | Flashes (green) for 30 seconds |
| System malfunction | Flashes (amber) for 15 seconds | Flashes (amber) for 15 seconds |
| Stop light switch with shift lever in P or N malfunction | Flashes (green) for 15 seconds | Flashes (green) for 15 seconds |
Main body ECU:
The main body ECU consists of the LH-IG relay 1 and IG2 relay actuation circuits and CPU.
WHEN KEY BATTERY IS LOW
To operate the push-button start function when the key battery is low, hold the key so that its TOYOTA mark is against the engine switch while depressing the brake pedal with the shift lever in P or N.
The main body ECU transmits a key verification request signal from the stop light switch to the certification ECU.
The certification ECU does not receive an ID code response from the door control receiver, so it actuates the transponder key amplifier built into the engine switch.
The transponder key amplifier outputs an engine immobiliser radio wave to the key.
The key receives the radio wave, and returns a radio wave response to the transponder key amplifier.
The transponder key amplifier combines the key ID codes with the radio wave response, and transmits it to the certification ECU.
The certification ECU judges and verifies the ID code, and transmits a key verification OK signal to the main body ECU. The buzzer in the combination meter sounds at the same time.
After the buzzer sounds, with the shift lever in P or N, if the engine switch is pressed within 5 seconds with the brake pedal not depressed, the power source mode changes to on (ACC) or on (IG), as in the normal condition.
DIAGNOSIS
The main body ECU can detect malfunctions in the push-button start function when the power source mode is on (IG).
When the ECU detects a malfunction, the amber indicator light of the engine switch flashes to warn the driver. At the same time, the ECU stores the 5-digit DTC (Diagnostic Trouble Code) in memory.
The indicator light warning continues for 15 seconds even after the power source mode is changed to off.
The DTC can be read by connecting the intelligent tester to the DLC3.
The push-button start function cannot be operated if a malfunction occurs.