READ DATA LIST
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Body / Body ECU / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG SW | Ignition switch on (IG) / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| ACC SW | Ignition switch on (ACC) / ON or OFF | ON: Ignition switch is on (ACC)
OFF: Ignition switch is off |
- |
| St SW1 | Start switch 1 / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| St SW2 | Start switch 2 / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| Str Unlock SW | Steering lock condition / ON or OFF | ON: Steering is unlocked
OFF: Steering is locked |
- |
| N SW / C SW | Park / neutral position switch / ON or OFF | ON: Shift lever in P or N
OFF: Shift lever in R or D |
- |
| Vehicle Spd Sig | Vehicle speed signal / STOP or RUN | STOP: Vehicle is stopped
RUN: Vehicle is running |
- |
| E/G Cond | Engine condition / STOP or RUN | STOP: Engine is stopped
RUN: Engine is running |
- |
| IG1 Relay Mon1 | LH-IG relay 1 outer relay monitor / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| IG2 Relay Mon1 | IG2 outer relay monitor / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| IG1 Relay Mon2 | LH-IG relay 1 inner relay monitor / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| IG2 Relay Mon2 | IG2 inner relay monitor / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| ACC Relay Mon | ACC relay monitor / ON or OFF | ON: Ignition switch is on (ACC)
OFF: Ignition switch is off |
- |
| Ratch Circuit | Ratch circuit / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off, on (ACC) or engine is running |
- |
| Start Req Sig | Starter request signal / ON or OFF | ON: ST relay is ON
OFF: ST relay is OFF |
- |
| Pwr Cond | Power supply condition / ALL, ACC ON, IG1 IG2, ST ON | ALL: All relays are ON
ACC ON: ACC relay is ON IG1: IG1 relay is ON IG2: IG2 relay is ON ST ON: ST relay is ON |
- |
| St Relay Mon | Starter relay monitor / ON or OFF | ON: Starter relay is ON
OFF: Starter relay is OFF |
- |
| #Code | Number of diagnosis codes / Min: 0, Max: 255 | - | - |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal is depressed
OFF: Brake pedal is released |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG SW | Ignition switch / ON or OFF | ON: Ignition switch is on (IG)
OFF: Ignition switch is off |
- |
| ACC SW | Ignition switch / ON or OFF | ON: Ignition switch is on (ACC)
OFF: Ignition switch is off |
- |
| Low Battery | Electrical key battery conditions / ON or OFF | ON: Battery is depleted
OFF: Battery is not depleted |
- |
| Unmatch Format | Code format / YES or NO | YES: Code format matches
NO: Code format differs |
- |
| No response | Response / YES or NO | YES: Response
NO: No response |
- |
| Wrong Code | ID code / YES or NO | YES: ID code matches
NO: ID code differs |
- |
| Wrong C Code | Challenge code / YES or NO | YES: Challenge code matches
NO: Challenge code differs |
- |
| Unmatch V-ID | Key number / YES or NO | YES: Key number matches
NO: Key number differs |
- |
| Permit (Start) | Engine start permission by certification ECU / PERMIT or PROHIBIT | PERMIT: Engine start is permitted
PROHIBIT: Engine start is prohibited |
- |
| Start Rqst | Starter request signal / YES or NO | YES: ID code box receives immobiliser unset signal
NO: ID code box does not receive immobiliser unset signal |
- |
| S Code Chk | S code certification result / NG or OK | NG: S code certification result is abnormal
OK: S code certification result is normal |
- |
| L Code Chk | L code certification result / NG or OK | NG: L code certification result is abnormal
OK: L code certification result is normal |
- |
PERFORM ACTIVE TEST
Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester ON.
Select the following menu items: Body / Body ECU / Active Test.
Perform the Active Test by referring to the table below.
| Tester Display | Test Part | Control Range |
|---|---|---|
| Lighting Ind | Indicator illumination
ON/OFF |
- |
| Ind Condition | Indicator light illumination pattern
Green/Amber/No Sig |
- |
| S Lock Pwr | Steering lock ECU power supply
ON/OFF |
- |
| Tester Display | Test Part | Control Range |
|---|---|---|
| Fr Transmitter | Indoor electrical key antenna (for front)
ON / OFF |
- |
| Rr Transmitter | Indoor electrical key antenna (for rear1)
ON / OFF |
- |
| In Bdr Trnsmttr | Indoor electrical key antenna (for rear2)
ON / OFF |
- |