Home › Engine / Hybrid System › 2AZ-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292080 SMART ENTRY AND START SYSTEM C

2AZ-FE STARTING  SMART ENTRY AND START SYSTEM  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is output when the IG output circuits inside the main body ECU are open or shorted.

DTC No. DTC Detection Condition Trouble Area
B2271 LH-IG relay 1 actuation circuit or IG2 relay actuation circuit inside main body ECU is abnormal
·

Main body ECU


·

AM2 NO. 2 fuse


·

Wire harness



WIRING DIAGRAM

A138964E06
5.542,2.906 6.625,3.156 1.083,0.25 10 false Main Body ECU 5,1.25 5.302,1.417 0.302,0.167 10 false G58 5,0.615 5.302,0.781 0.302,0.167 10 false G57 5.083,1.063 5.188,1.208 0.104,0.146 10 false 1 5.083,0.427 5.198,0.583 0.115,0.156 10 false 6 5.031,2.323 5.229,2.479 0.198,0.156 10 false 4A 5.073,2.146 5.188,2.292 0.115,0.146 10 false 3 2.208,0.781 2.969,1.031 0.76,0.25 10 false AM2 NO. 2 0.51,1.594 1.406,1.781 0.896,0.188 10 false from Battery 5.323,0.604 5.646,0.76 0.323,0.156 10 false AM1 5.344,1.219 5.698,1.385 0.354,0.167 10 false AM2 5.333,2.302 5.792,2.469 0.458,0.167 10 false GND2

PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Clear the DTCs.


d.

Start the engine.


e.

Allow the engine to idle for 1 minute or more.


f.

Select the following menu items: Body / Body ECU / DTC.


g.

Read DTCs.

Result:
Display (DTC output) Proceed to
B2271 A
No DTC output B




A

2.INSPECT FUSE (AM2 NO. 2)

B

END (SYSTEM IS OK)

2.INSPECT FUSE (AM2 NO. 2)
a.

Remove the AM2 NO. 2 fuse from the engine room No. 1 relay block.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY AND BODY GROUND)
U188709E02
2.625,1.406 2.844,2.083 false 1.646,1.406 1.865,2.073 false 5.042,1.49 5.24,2.208 false 0.135,0.052 1.885,0.219 1.75,0.167 10 false Wire Harness Side: 1.031,0.625 1.333,0.771 0.302,0.146 10 false G57 2.958,0.635 3.25,0.802 0.292,0.167 10 false G58 5.469,0.625 5.719,0.813 0.25,0.188 10 false 4A 1.76,2.094 2.073,2.26 0.313,0.167 10 false AM1 2.76,2.104 3.104,2.271 0.344,0.167 10 false AM2 5.125,2.24 5.583,2.406 0.458,0.167 10 false GND2

a.

Disconnect the G57, G58 and 4A main body ECU connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Standard voltage:
Tester Connection Specified Condition
G58-1 (AM2) - Body ground 10 to 14 V
G57-6 (AM1) - Body ground 10 to 14 V


Standard resistance:
Tester Connection Specified Condition
4A-3 (GND2) - Body ground Below 1 Ω




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR