Home › Engine / Hybrid System › 2AZ-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292080 SMART ENTRY AND START SYSTEM C

2AZ-FE STARTING  SMART ENTRY AND START SYSTEM  B2287  LIN Communication Master Malfunction  


DESCRIPTION

DTC B2287 is output when there is an abnormal LIN communication circuit between the main body ECU and the certification ECU.

DTC No. DTC Detection Condition Trouble Area
B2287 Communication or communication line is abnormal between main body ECU and certification ECU
·

Main body ECU

·

Certification ECU

·

Wire harness



A393979E01
3.208,0.604 4.698,0.865 1.49,0.26 10 false B2289 Detection Area 0.76,0.833 1.927,1.094 1.167,0.26 10 false Main Body ECU 2.344,1.917 3.781,2.167 1.438,0.25 10 false B2287 Detection Area 1.896,2.271 2.417,2.521 0.521,0.25 10 false LIN1 2.385,2.448 2.958,2.698 0.573,0.25 10 false LIN Line 4.25,2.146 5.458,2.438 1.208,0.292 10 false Certification ECU 4.125,2.865 5.51,3.146 1.385,0.281 10 false Steering Lock ECU 4.333,3.604 5.167,3.844 0.833,0.24 10 false ID Code Box 6.115,2.958 7.01,3.229 0.896,0.271 10 false Electrical Key 3.01,4.74 4,4.99 0.99,0.25 10 false Engine Switch 0.813,5.104 4.115,5.406 3.302,0.302 10 false *: This DTC is set when there is a malfunction 1.698,4.073 2.219,4.323 0.521,0.25 10 false B2278* 1.781,4.25 2.302,4.5 0.521,0.25 10 false SSW1 1.781,4.396 2.302,4.646 0.521,0.25 10 false SSW2

WIRING DIAGRAM

A393977E03
1.26,1.958 1.844,2.208 0.583,0.25 10 false LIN 1.646,1.844 2.229,2.094 0.583,0.25 10 false 10 5.427,1.823 6.01,2.073 0.583,0.25 10 false 20 5.729,1.958 6.313,2.208 0.583,0.25 10 false LIN1 0.438,3.021 1.021,3.271 0.583,0.25 10 false G29 0.448,3.188 1.76,3.438 1.313,0.25 10 false Certification ECU 5.708,3.031 6.292,3.281 0.583,0.25 10 false 4A 5.708,3.198 6.771,3.458 1.063,0.26 10 false Main Body ECU

PROCEDURE

1.CHECK WIRE HARNESS (MAIN BODY ECU - CERTIFICATION ECU)
a.

Disconnect the 4A main body ECU connector.


b.

Disconnect the G29 certification ECU connector.


c.
A394000E01
1.417,0.583 1.833,0.833 0.417,0.25 1.563,2.833 1.979,3.083 0.417,0.25 1.271,1.51 0.677,0.781 false 2.229,3.635 2.708,3.125 false 0.125,0.094 1.448,0.344 1.323,0.25 10 false Wire Harness Side: 0.323,0.688 0.938,0.885 0.615,0.198 10 false LIN1 1.531,0.615 2.146,0.813 0.615,0.198 10 false 4A 1.635,2.865 2.25,3.063 0.615,0.198 10 false G29 2.76,2.958 3.177,3.188 0.417,0.229 10 false LIN 1.302,4.229 2.594,4.479 1.292,0.25 10 false Certification ECU 1.229,2.01 2.521,2.26 1.292,0.25 10 false Main Body ECU

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
4A-20 (LIN1) - G29-10 (LIN) Below 1 Ω
4A-20 (LIN1) or G29-10 (LIN) - Body ground 10 kΩ or higher




OK

2.CHECK OPERATION OF MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK OPERATION OF MAIN BODY ECU
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check for DTCs again.

OK:

No DTC is output.




OK

END (MAIN BODY ECU IS FAULTY)

NG

REPLACE CERTIFICATION ECU