Home › Engine / Hybrid System › 2AZ-FE STARTING › SMART ENTRY AND START SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292080 SMART ENTRY AND START SYSTEM C

2AZ-FE STARTING  SMART ENTRY AND START SYSTEM  B2286  Runnable Signal Malfunction  


DESCRIPTION

The main body ECU and the ECM are connected by a cable and the CAN communication line. If the cable information and CAN information are inconsistent, this DTC is output.

DTC No. DTC Detection Condition Trouble Area
B2286 Cable and CAN information between main body ECU and ECM are inconsistent
·

Main body ECU


·

SFI system


·

Wire harness



WIRING DIAGRAM

A394003E01
1.01,1.146 1.813,1.427 0.802,0.281 10 false CANH 1.01,1.75 1.813,2.031 0.802,0.281 10 false CANL 1.031,2.365 1.833,2.646 0.802,0.281 10 false TACH 0.583,2.854 1.385,3.135 0.802,0.281 10 false A7 0.583,3.01 1.385,3.292 0.802,0.281 10 false ECM 1.552,2.219 2.354,2.5 0.802,0.281 10 false 15 1.542,1.615 2.344,1.896 0.802,0.281 10 false 49 1.552,1.01 2.354,1.292 0.802,0.281 10 false 41 3.198,1.323 4,1.604 0.802,0.281 10 false CAN Line 5.396,1.625 6.198,1.906 0.802,0.281 10 false 6 5.396,1.01 6.198,1.292 0.802,0.281 10 false 5 5.396,2.24 6.198,2.521 0.802,0.281 10 false 8 5.635,2.875 6.438,3.156 0.802,0.281 10 false G59 5.635,3.042 6.708,3.302 1.073,0.26 10 false Main Body ECU 3.208,1.948 4.01,2.229 0.802,0.281 10 false CAN Line 5.656,1.125 6.458,1.406 0.802,0.281 10 false CANH 5.646,1.74 6.448,2.021 0.802,0.281 10 false CANL 5.656,2.333 6.458,2.615 0.802,0.281 10 false TACH

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE CONDITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / Main Body ECU / Data List / E/G Cond.


d.

Read the display on the tester.

Main body ECU:
Item Measurement Item/Display (Range) Normal Condition Diagnostic Note
E/G Cond Engine condition / RUN or STOP RUN: Engine running
STOP: Engine stopped
-


OK:

When the engine is running, RUN is displayed on the tester.




NG

2.CHECK WIRE HARNESS (MAIN BODY ECU - ECM)

OK

REPLACE MAIN BODY ECU

2.CHECK WIRE HARNESS (MAIN BODY ECU - ECM)
a.

Disconnect the G59 main body ECU connector.

A393999E01
1.583,0.5 2,0.75 0.417,0.25 4,0.333 4.417,0.583 0.417,0.25 1.885,1.594 2.5,1.375 false 4.385,2.344 5.688,1.219 false 0.125,0.104 1.635,0.344 1.51,0.24 10 false Wire Harness Side: 1.656,0.531 2.156,0.781 0.5,0.25 10 false G59 2.552,1.25 3.052,1.5 0.5,0.25 10 false TACH 4.125,0.365 4.625,0.615 0.5,0.25 10 false A7 1.344,2.146 2.531,2.385 1.188,0.24 10 false Main Body ECU 5.219,2.281 5.719,2.531 0.5,0.25 10 false ECM 3.958,2.281 4.458,2.531 0.5,0.25 10 false TACH


b.

Disconnect the A7 ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G59-8 (TACH) - A7-15 (TACH) Below 1 Ω
G59-8 (TACH) or A7-15 (TACH) - Body ground 10 kΩ or higher




OK

3.CHECK WHETHER ENGINE STARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER ENGINE STARTS
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check that the engine starts normally.

OK:

Engine starts normally.




OK

END (MAIN BODY ECU IS FAULTY)

NG