Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START U

2AZ-FE STARTING  PUSH-BUTTON START  TERMINALS OF ECU  


CHECK MAIN BODY ECU


U188403E02
5.844,3.875 6.115,2.448 false 6.042,2.26 6.229,2.427 0.188,0.167 10 false *B 3.573,1.875 3.74,2.052 0.167,0.177 10 false *A 2.688,4.135 3.25,4.479 0.563,0.344 10 false 4A 4.292,5.479 4.854,5.823 0.563,0.344 10 false 4K 6.406,4.25 6.969,4.594 0.563,0.344 10 false G57 6.406,5 6.969,5.344 0.563,0.344 10 false G58 6.406,5.635 6.969,5.979 0.563,0.344 10 false G59 6.406,6.094 6.969,6.438 0.563,0.344 10 false G60

Text in Illustration
*A Instrument Panel Junction Block LH *B Main Body ECU

a.

Disconnect the G57, G58 and G59 main body ECU connectors.


b.

Disconnect the 4K and 4A instrument panel junction block LH connectors.


c.

Measure the voltage and resistance of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
BATB (4K-9) - Body ground B - Body ground +B power supply Always 10 to 14 V
AM1 (G57-6) - Body ground SB - Body ground +B power supply Always 10 to 14 V
AM2 (G58-1) - Body ground SB - Body ground +B power supply Always 10 to 14 V
SSW1 (G57-17) - Body ground P - Body ground Engine switch 1 input Engine switch pushed Below 1 Ω
SSW1 (G57-17) - Body ground P - Body ground Engine switch 1 input Engine switch not pushed 10 kΩ or higher
SSW2 (G57-16) - Body ground G - Body ground Engine switch 2 input Engine switch pushed Below 1 Ω
SSW2 (G57-16) - Body ground G - Body ground Engine switch 2 input Engine switch not pushed 10 kΩ or higher
GND1 (G59-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
GND2 (4A-3) - Body ground W-B - Body ground Ground Always Below 1 Ω
LIN1 (4A-20) - Body ground R - Body ground LIN line Always 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.



d.

Reconnect the G57, G58 and G59 main body ECU connectors.


e.

Reconnect the 4K and 4A instrument panel junction block LH connectors.


f.

Measure the voltages of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
ACCD (G57-22) - GND2 (4A-3) GR - W-B ACC relay drive signal Engine switch on (ACC) 10 to 14 V
ACCD (G57-22) - GND2 (4A-3) GR - W-B ACC relay drive signal Engine switch off Below 1 V
IG2D (G58-11) - GND2 (4A-3) G - W-B IG2 relay drive signal Engine switch on (IG) 10 to 14 V
IG2D (G58-11) - GND2 (4A-3) G - W-B IG2 relay drive signal Engine switch on (ACC) Below 1 V
SLR+ (G57-19) - GND2 (4A-3) L - W-B Steering lock power supply Steering lock motor operating Below 1 V
SLR+ (G57-19) - GND2 (4A-3) L - W-B Steering lock power supply Steering lock motor not operating 10 to 14 V
SLP (G57-18) - GND2 (4A-3) Y - W-B Steering lock actuator position signal Steering lock locked 10 to 14 V
SLP (G57-18) - GND2 (4A-3) Y - W-B Steering lock actuator position signal Steering lock released Below 1 V
SPD (G59-9) - GND2 (4A-3) W - W-B Speed signal from combination meter Engine switch on (IG), Rotate driving wheel slowly Pulse generation
(see waveform 1)
TACH (G59-8) - GND2 (4A-3) R - W-B Tachometer signal Engine running Pulse generation
(see waveform 2)
STSW (G60-4) - GND2 (4A-3) P - W-B Starter activation request signal Brake pedal depressed with shift lever in P or N, engine switch pushed once 10 to 14 V*
STR (G57-8) - GND2 (4A-3) G - W-B Park / neutral position switch Shift lever in P or N Below 1 V
STR2 (G60-6) - GND2 (4A-3) SB - W-B Starter signal Brake pedal depressed with shift lever in P or N, engine switch pushed once 10 to 14 V*
INDS (G57-15) - GND2 (4A-3) Y - W-B Vehicle condition signal Brake pedal depressed with shift lever in P or N, engine switch off, on (ACC, IG) 9 to 14 V
INDW (G57-14) - GND2 (4A-3) GR - W-B Vehicle condition signal Brake pedal released with shift lever in P or N, engine switch off, on (ACC, IG) 9 to 14 V
SWIL (G57-25) - GND2 (4A-3) SB- W-B Illumination signal Light control switch TAIL or HEAD 10 to 14 V
STP (4K-7) - GND2 (4A-3) L- W-B Stop light switch signal Brake pedal depressed 10 to 14 V

HINT:

*: Voltage is output for 0.3 seconds before the engine is started.


If the result is not as specified, the ECU may have a malfunction.


g.
I042329E28
2.844,1.24 3.25,1.438 0.406,0.198 10 false GND 0.104,0.021 1,0.177 0.896,0.156 10 false Waveform 1:

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Symbols (Terminal No.) SPD (G59-9) - GND2 (4A-3)
Tool setting 5 V/DIV., 10 msec./DIV
Condition Driving at approx. 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the wavelength shortens.



h.
I042330E32
2.896,1.25 3.333,1.448 0.438,0.198 10 false GND 0.094,0 1.052,0.167 0.958,0.167 10 false Waveform 2:

Using an oscilloscope, check waveform 2.

Waveform 1 (Reference)
Item Content
Symbols (Terminal No.) TACH (G59-8) - GND2 (4A-3)
Tool setting 5 V/DIV., 10 msec./DIV
Condition Engine idling

HINT:

As the vehicle speed increases, the wavelength shortens.




CHECK CERTIFICATION ECU


U188567E02
3.49,0.302 3.771,0.479 0.281,0.177 10 false G29

a.

Disconnect the G29 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
+B1 (G29-1) - Body ground BE - Body ground +B power supply Always 10 to 14 V
LIN (G29-10) - Body ground R - Body ground LIN line Always 10 kΩ or higher
E (G29-17) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G29 ECU connector.


d.

Measure the voltage of the connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
IG (G29-18) - Body ground B - Body ground Ignition power supply Engine switch on (IG) 10 to 14 V
IG (G29-18) - Body ground B - Body ground Ignition power supply Engine switch off Below 1 V
CLG5 (G29-11) - CG5B (G29-12) P - V Indoor electrical key antenna (for front) sensor signal 30 seconds after driver side door opened and closed, engine switch off Hz output → no Hz output
CLG6 (G29-13) - CG6B (G29-14) B - Y Indoor electrical key antenna (for rear1) sensor signal 30 seconds after driver side door opened and closed, engine switch off Hz output → no Hz output
CLG7 (G29-15) - CG7B (G29-16) B - G Indoor electrical key antenna (for rear2) sensor signal 30 seconds after driver side door opened and closed, engine switch off Hz output → no Hz output
CLG8 (G29-31) - CG8B (G29-32) BR - GR Back door electrical key antenna (for outer) sensor signal With engine switch OFF and doors closed, back door unlock switch OFF → ON Hz output → no Hz output
RCO (G29-29) - E (G29-17) P - W-B Door control receiver power source Engine switch off, all doors closed and transmitter switch not pressed → pressed Below 1 V → 4.6 to 5.4 V → Below 1 V
RSSI (G29-39) - E (G29-17) BE - W-B Door control receiver electric wave existence signal Engine switch off, all doors closed and transmitter switch not pressed → pressed 10 to 14 V → Below 1 V
RDA (G29-38) - E (G29-17) V - W-B Door control receiver data input signal Engine switch off, all doors closed and transmitter switch not pressed → pressed Below 1 V → 10 to 14 V → Below 1 V

If the result is not as specified, the ECU may have a malfunction.




CHECK ECM


U188990E02
5.094,0.406 5.292,0.552 0.198,0.146 10 false A7 2.646,0.396 2.854,0.542 0.208,0.146 10 false D2

a.

Disconnect the A7 and D2 ECM connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
BATT (A7-20) - E1 (D2-104) W - BR Battery (for measuring battery voltage and for ECM memory) Always 10 to 14 V
+B (A7-2) - E1 (D2-104) B - BR Power source of ECM Engine switch on (IG) 10 to 14 V
+B2 (A7-1) - E1 (D2-104) B - BR Power source of ECM Engine switch off 10 to 14 V
IGSW (A7-28) - E1 (D2-104) BE - BR Engine switch signal Always 10 to 14 V
E1 (D2-104) - Body ground BR - Body ground Ground Always Below 1 Ω
E02 (D2-44) - Body ground BR - Body ground Ground Always Below 1 Ω
E04 (D2-46) - Body ground BR - Body ground Ground Always Below 1 Ω
E01 (D2-45) - Body ground BR - Body ground Ground Always Below 1 Ω
E03 (D2-86) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the A7 and D2 ECM connectors.


d.

Measure the voltage of the connectors.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
STA (A7-48) - E1 (D2-104) B - BR Starter relay operation signal Cranking 5.5 V or more
ACCR (A7-13) - E1 (D2-104) GR - BR ACC relay cut signal
(output)
Engine switch on (IG) → Cranking 10 to 14 V → Below 1 V
TACH (A7-15) - E1 (D2-104) B - BR Engine revolution signal
(output)
Idling Pulse generation
(see waveform 1)
STAR (D2-52) - E1 (D2-104) G - BR Starter relay drive signal Cranking 10 to 14 V

If the result is not as specified, the ECM may have a malfunction.



e.
I042330E33
2.896,1.24 3.333,1.438 0.438,0.198 10 false GND 0.063,0 1.135,0.156 1.073,0.156 10 false Waveform 1:

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Symbols (Terminal No.) TACH (A7-15) - E1 (D2-104)
Tool setting 5 V/DIV., 10 msec./DIV
Condition Engine idling

HINT:

As the vehicle speed increases, the wavelength shortens.




CHECK STEERING LOCK ECU


U188552E02
3.438,0.271 3.75,0.469 0.313,0.198 10 false G32

a.

Disconnect the G32 ECU connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
B (G32-7) - Body ground B - Body ground +B power supply Always Always
IG2 (G32-6) - Body ground B - Body ground Ignition power supply Engine switch on (IG) Always
IG2 (G32-6) - Body ground B - Body ground Ignition power supply Engine switch off Below 1 V
GND (G32-1) - Body ground W-B - Body ground Ground Always Below 1 Ω
SGND (G32-2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.