Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START D

2AZ-FE STARTING  PUSH-BUTTON START  SYSTEM DESCRIPTION  


PUSH-BUTTON START DESCRIPTION


a.

The push-button start uses a push-type engine switch, which the driver can operate by merely carrying the key. This system consists primarily of the main body ECU, engine switch, ID code box, steering lock ECU, key, ACC relay, LH-IG relay 1, IG2 relay and certification ECU. The main body ECU controls the system. This function operates in cooperation with the push-button start. The table below shows the transition of the engine switch, which depends on whether the brake pedal is depressed or released.


b.

This system has different power source mode patterns depending on the brake pedal and shift lever conditions.

Condition Power Source Mode Pattern
Brake pedal not depressed, shift lever in P Each time engine switch is pushed
·

off → on (ACC) → on (IG) → off


Brake pedal not depressed When engine switch is pushed in engine started condition
·

Engine started → off


Brake pedal depressed, shift lever in P or N When engine switch is pushed once
·

off → engine start


Brake pedal depressed, shift lever in P or N When engine switch is pushed in on (ACC) condition
·

on (ACC) → engine start


Brake pedal depressed, shift lever in P or N When engine switch is pushed in on (IG) condition
·

on (IG) → engine start


Brake pedal depressed When engine switch is pushed in engine started condition
·

Engine started → off



When the battery of the key is low, the push-button start function can be operated by holding the key against the engine switch.



FUNCTION OF COMPONENT


Components Function
Engine Switch
(Transponder Key Amplifier)
·

Transmits engine switch signal to main body ECU.

·

Informs driver of power source mode or system abnormality with indicator light illumination.

·

Receives ID code and transmits it to certification ECU when battery of key is low.


Key
·

Receives signals from oscillators and returns ID code to door control receiver.


Indoor Electrical Key Oscillator
·

Receives request signal from certification ECU and forms detection area in vehicle interior.


Door Control Receiver
·

Receives ID code from key and transmits it to certification ECU.


Main Body ECU
·

Changes power source mode in 4 stages (off, on (ACC), on (IG), start) in accordance with state of park / neutral position switch.

·

Controls push-button start function in accordance with signals received from switches and each ECU.


Certification ECU
·

Certifies ID code received from door control receiver and transmits certification results to ID code box and steering lock ECU.


Park / Neutral Position Switch
·

Outputs state of shift position to main body ECU.


Stop Light Switch
·

Outputs state of brake pedal to main body ECU.


ID Code Box
·

Receives steering unlock or engine immobiliser unset signals from certification ECU, certifies them, and transmits each unset signal to steering lock ECU or ECM.


ECM
·

Receives engine start request signal from power source control ECU, turns ON ST relay, and starts engine.

·

Receives signal from ID code box and performs engine ignition and fuel injection.




SYSTEM FUNCTION


The electric controls of the push-button start function are described below:

Control Outline
Engine Switch Control
·

When driver operates engine switch with key in driver's possession, certification ECU starts indoor electrical key oscillator, which transmits request signal to key. Upon receiving this signal, key transmits ID code signal to main body ECU.

·

ID code box verifies check results received from certification ECU via LIN line and sends them to main body ECU. Based on these results, main body ECU authorizes operation of engine switch.


Diagnosis
·

When main body ECU detects malfunction, main body ECU diagnoses and memorizes failed section.




CONSTRUCTION AND OPERATION


A109251E21
1.375,0.781 1.646,0.208 1.646,0.208 1.917,0.208 true 1.979,0.135 3.104,0.344 1.125,0.208 10 Indicator Light

a.

Engine switch:

The engine switch consists of a momentary type switch, 3 color (amber, green, greenish white) LEDs, and transponder key amplifier.

·

The greenish white LED is for illumination.

·

The amber and green LEDs are for the indicator lights. The driver can check the present power source mode and whether the engine can start or not in accordance with the illumination state of the indicator light.

·

When the main body ECU detects an abnormality in the push-button start, it makes the amber indicator light flash. If the engine is stopped in this state, it might not be possible to restart it.


Text in Illustration
*A Indicator Light


b.

Indicator light condition:

Engine switch indicator light condition
Power Source Mode/Condition Indicator Light Condition
Brake pedal released Brake pedal depressed, shift lever in P or N
Off OFF Illuminates (green)
On (ACC, IG) Illuminates (amber) Illuminates (green)
Engine running OFF OFF
Steering lock locked Flashes (green) for 30 seconds Flashes (green) for 30 seconds
System malfunction Flashes (amber) for 15 seconds Flashes (amber) for 15 seconds
Stop light switch with shift lever in P or N malfunction Flashes (green) for 15 seconds Flashes (green) for 15 seconds


c.

Main body ECU:

The main body ECU consists of the LH-IG relay 1 and IG2 relay actuation circuits and CPU.



WARNING FUNCTION


a.

General:

When any of the situations below occur, the push-button start responds to alert the driver.

Warning Function Operation Condition Situation Situation
Shift lever not on P (power source cut reminder) vehicle exit warning A
Key reminder warning B
Shift lever on P (power source cut reminder) vehicle exit warning C
Passenger has brought key out of vehicle warning D
Key is not within detection area warning E
Key battery low warning F


b.

Situation A:

Shift lever not on P (power source cut reminder) vehicle exit warning

i.

With shift lever in position other than P, door is opened and vehicle exit (while holding key) is attempted

Reason for warning: Sudden vehicle start prevention, vehicle theft prevention, vehicle roll-away prevention
Warning start condition: Shift lever position is not P, engine switch is on (ACC or IG), driver side door is opened and vehicle speed is 0 km/h (0 mph)
Warning stop condition: Engine switch is on (ACC or IG), shift lever position is P, vehicle speed is above 0 km/h (0 mph), or driver side door is closed
Warning description Combination meter buzzer Short sound buzzer Sounds continuously (beep)
Combination meter display Telltale None
Wireless buzzer None
Recommended user action Move shift lever to P position


ii.

With shift lever in position other than P, door is opened, key is brought out of vehicle, door is closed, and move away from vehicle is attempted

Reason for warning: Sudden vehicle start prevention, vehicle theft prevention, vehicle roll-away prevention
Warning start condition: Shift lever position is not P, engine switch is on (ACC or IG), opened driver side door is closed, vehicle speed is 0 km/h (0 mph) and key is not in detected in vehicle interior
Warning stop condition:
·

Key is detected in vehicle interior:

Buzzer stops



·

Vehicle speed is above 0 km/h (0 mph):

Buzzer stops and telltale illuminates



·

Engine switch on (ACC) or off:

All warnings are turned off



Warning description Combination meter buzzer Short sound buzzer Sounds continuously (beep)
Combination meter display Telltale Illuminates
Wireless buzzer Sounds continuously (beep)
Recommended user action Move shift lever to P position



c.

Situation B:

Key reminder warning

i.

With shift lever on P and either engine switch on (ACC), or steering lock / unlock set, driver door is opened and move away from vehicle is attempted

Reason for warning: Vehicle theft prevention, required by law
Precondition: Remote engine starter is not operating
Warning start condition: With shift lever position in P, one of following conditions is met
1.

Engine switch on (ACC) or off, and driver door opened

2.

Engine switch on (ACC) or off, steering lock/unlock set and driver door opened


Warning stop condition: One of following conditions is met
1.

With shift lever position in P, engine switch is on (IG) or driver door is closed

2.

Engine switch on (ACC) or off, and steering lock/unlock is set


Warning description Combination meter buzzer Short sound buzzer Sounds intermittently (several short beeps)
Combination meter display Telltale None
Wireless buzzer None
Recommended user action One of following is performed
1.

Turn engine switch off and close driver door

2.

Close driver door





d.

Situation C:

Shift lever on P (power source cut reminder) vehicle exit warning

i.

Pattern 1: With shift lever on P, driver door is opened, key is brought out of vehicle, driver door is closed, and move away from vehicle is attempted

Reason for warning: Vehicle theft prevention, "engine cannot be restarted" prevention, battery depletion prevention
Warning start condition: Shift lever position is P, engine switch is on (ACC or IG), opened driver side door is closed and key is not in detected in vehicle interior
Warning stop condition: Engine switch on (ACC) or off, or key is detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
(when key is not detected continuously, sounds again when vehicle is first driven)
Combination meter display Telltale Illuminates
Wireless buzzer Sounds 3 times (short beeps)
Recommended user action Turn engine switch off and exit vehicle while holding key



e.

Situation D:

Passenger has brought key out of vehicle warning

i.

With engine switch in position other than off, key is brought out of vehicle by passenger

Reason for warning: "Engine cannot be started" prevention
Warning start condition: Engine switch is on (ACC or IG), opened door other than driver side door is closed, vehicle speed is 0 km/h (0 mph) and key is not in detected in vehicle interior
Warning stop condition: Engine switch on (ACC) or off, or key is detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
(when key is not detected continuously, sounds again when vehicle is first driven)
Combination meter display Telltale Illuminates
Wireless buzzer Sounds 3 times (short beeps)
Recommended user action Check if the passenger who exited the vehicle has the key or not



f.

Situation E:

Key is not within detection area warning

i.

With key not in vehicle cabin or key battery depleted, engine start is attempted or engine switch on (ACC or IG) operation is attempted

Reason for warning: User confusion prevention
Warning condition: Engine switch is not off and key is not detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
Combination meter display Telltale Illuminates for 8 seconds or less
Wireless buzzer None
Recommended user action Check if the key is within the detection area of the vehicle cabin.
If key is within the vehicle interior, built-in battery may be depleted
If key's wireless door lock switch is pressed, check if key's indicator illuminates
If indicator does not illuminate, replace the built-in battery
It is recommended that battery be bought at dealer, but battery can be replaced according to user preference



g.

Situation F:

Key battery low warning

i.

Key with almost depleted battery is used to drive vehicle

Reason for warning: Helpful function
Warning condition: After engine switch not off condition continues for 20 minutes or more, engine switch is changed from not off to off position, key battery is low and key is detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
Combination meter display Telltale None
Wireless buzzer None
Recommended user action Replace key's built-in battery with new one
It is recommended that battery be bought at dealer, but battery can be replaced according to user preference




WHEN KEY BATTERY IS LOW


A139316E03
1.185,2.924 1.358,3.105 0.173,0.180 10 *A 2.121,3.964 2.292,4.155 0.170,0.191 10 *B 1.714,1.234 1.893,1.397 0.180,0.163 10 *a

a.

To operate the push-button start function when the key battery is low, hold the key so that its TOYOTA mark is against the engine switch while depressing the brake pedal with the shift lever in P or N.


b.

The main body ECU transmits a key verification request signal from the stop light switch to the certification ECU.


c.

The certification ECU does not receive an ID code response from the door control receiver, so it actuates the transponder key amplifier built into the engine switch.


d.

The transponder key amplifier outputs an engine immobiliser radio wave to the key.


e.

The key receives the radio wave, and returns a radio wave response to the transponder key amplifier.


f.

The transponder key amplifier combines the key ID codes with the radio wave response, and transmits it to the certification ECU.


g.

The certification ECU judges and verifies the ID code, and transmits a key verification OK signal to the main body ECU. The buzzer in the combination meter sounds at the same time.


h.

After the buzzer sounds, with the shift lever in P or N, if the engine switch is pressed within 5 seconds with the brake pedal not depressed, the power source mode changes to on (ACC) or on (IG), as in the normal condition.

Text in Illustration
*A Engine Switch
*B Electrical Key
*a Required Distance: 10 mm (0.39 in.)



DIAGNOSIS



The main body ECU can detect malfunctions in the push-button start function when the power source mode is on (IG).

When the ECU detects a malfunction, the amber indicator light of the engine switch flashes to warn the driver. At the same time, the ECU stores the 5-digit DTC (Diagnostic Trouble Code) in memory.

·

The indicator light warning continues for 15 seconds even after the power source mode is changed to off.

·

The DTC can be read by connecting the GTS to the DLC3.

·

The push-button start function cannot be operated if a malfunction occurs.