READ DATA LIST
Using the GTS's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body Electrical / Body ECU / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG SW | Engine switch on (IG) / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| ACC SW | Engine switch on (ACC) / ON or OFF | ON: Engine switch is on (ACC)
OFF: Engine switch is off |
- |
| Start SW1 | Start switch 1 / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| Start SW2 | Start switch 2 / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| Steering Unlock Switch | Steering lock condition / ON or OFF | ON: Steering is unlocked
OFF: Steering is locked |
- |
| Neutral SW/ Clutch SW | Park / neutral position switch / ON or OFF | ON: Shift lever in P or N
OFF: Shift lever in R or D |
- |
| Vehicle Speed Signal | Vehicle speed signal / STOP or RUN | STOP: Vehicle is stopped
RUN: Vehicle is running |
- |
| Engine Condition | Engine condition / STOP or RUN | STOP: Engine is stopped
RUN: Engine is running |
- |
| IG1 Relay Monitor(Outside) | LH-IG relay 1 outer relay monitor / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| IG2 Relay Monitor(Outside) | IG2 outer relay monitor / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| IG1 Relay Monitor(Inside) | LH-IG relay 1 inner relay monitor / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| IG2 Relay Monitor(Inside) | IG2 inner relay monitor / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| ACC Relay Monitor | ACC relay monitor / ON or OFF | ON: Engine switch is on (ACC)
OFF: Engine switch is off |
- |
| Ratch Circuit | Ratch circuit / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off, on (ACC) or engine is running |
- |
| Starter Request Signal | Starter request signal / ON or OFF | ON: ST relay is ON
OFF: ST relay is OFF |
- |
| Power Supply Condition | Power supply condition / ALL, ACC ON, IG1 IG2, ST ON | ALL: All relays are ON
ACC ON: ACC relay is ON IG1: IG1 relay is ON IG2: IG2 relay is ON ST ON: ST relay is ON |
- |
| Starter Relay Monitor | Starter relay monitor / ON or OFF | ON: Starter relay is ON
OFF: Starter relay is OFF |
- |
| The Number of DTC | Number of diagnosis codes / Min: 0, Max: 255 | - | - |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal is depressed
OFF: Brake pedal is released |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG SW | Engine switch / ON or OFF | ON: Engine switch is on (IG)
OFF: Engine switch is off |
- |
| ACC SW | Engine switch / ON or OFF | ON: Engine switch is on (ACC)
OFF: Engine switch is off |
- |
| Key Low Battery | Electrical key battery conditions / ON or OFF | ON: Battery is depleted
OFF: Battery is not depleted |
- |
| Unmatch Code or Form | Code format / YES or NO | YES: Code format matches
NO: Code format differs |
- |
| No response | Response / YES or NO | YES: Response
NO: No response |
- |
| ID Code Difference(Resp) | ID code / YES or NO | YES: ID code matches
NO: ID code differs |
- |
| C Code Difference | Challenge code / YES or NO | YES: Challenge code matches
NO: Challenge code differs |
- |
| Unmatched Vehicle-ID | Key number / YES or NO | YES: Key number matches
NO: Key number differs |
- |
| Permit (Start) | Engine start permission by certification ECU / PERMIT or PROHIBIT | PERMIT: Engine start is permitted
PROHIBIT: Engine start is prohibited |
- |
| Engine Start Request | Starter request signal / YES or NO | YES: ID code box receives immobiliser unset signal
NO: ID code box does not receive immobiliser unset signal |
- |
| S Code Check | S code certification result / NG or OK | NG: S code certification result is abnormal
OK: S code certification result is normal |
- |
| L Code Check | L code certification result / NG or OK | NG: L code certification result is abnormal
OK: L code certification result is normal |
- |
PERFORM ACTIVE TEST
Performing the GTS's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time. The Data List can be displayed during the Active Test.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the tester ON.
Select the following menu items: Body Electrical / Body ECU / Active Test.
Perform the Active Test by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicator for Lighting | Indicator illumination | ON/OFF | - |
| Indicator Condition | Indicator light illumination pattern | Green/Amber/No Sig | - |
| P Supply for Steering Lock | Steering lock ECU power supply | ON/OFF | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Fr-Seat Inside Transmitter | Indoor electrical key antenna (for front) | ON / OFF | - |
| Rr-Seat Inside Transmitter | Indoor electrical key antenna (for rear1) | ON / OFF | - |
| Inside Trunk/Backdoor Transmitter | Indoor electrical key antenna (for rear2) | ON / OFF | - |