Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START C

2AZ-FE STARTING  PUSH-BUTTON START  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is output when the engine start request signal circuit inside the main body ECU is open or shorted.

DTC No. DTC Detection Condition Trouble Area
B2275 Engine start request signal circuit inside main body ECU or other related circuit is malfunctioning
·

Main body ECU


·

SFI system


·

Wire harness



WIRING DIAGRAM

A393977E01
1.073,1.958 1.656,2.208 0.583,0.25 10 false STSW 1.646,1.844 2.229,2.094 0.583,0.25 10 false 14 5.5,1.823 6.083,2.073 0.583,0.25 10 false 4 5.729,1.958 6.313,2.208 0.583,0.25 10 false STSW 0.667,3.021 1.25,3.271 0.583,0.25 10 false A7 0.667,3.188 1.25,3.438 0.583,0.25 10 false ECM 5.698,3.031 6.281,3.281 0.583,0.25 10 false G60 5.708,3.198 6.771,3.458 1.063,0.26 10 false Main Body ECU

PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Clear the DTCs.


d.

Depress the brake pedal with the engine switch on (IG), wait at least 15 seconds, and check whether DTC B2275 recurs.

Result:
Display (DTC output) Proceed to
B2275 A
No DTC output B




A

2.CHECK MAIN BODY ECU (STSW VOLTAGE)

B

END (SYSTEM OK)

2.CHECK MAIN BODY ECU (STSW VOLTAGE)
a.

Disconnect the G60 main body ECU connector.


b.

With the shift lever in P or N, depress the brake pedal fully.


c.

Measure the voltage between the ECU terminal and the body ground when operating the engine switch to crank the engine.

HINT:

The voltage is generated at terminal STSW for 0.3 seconds when the engine cranks.


Standard voltage:
Tester Connection Specified Condition
G60-4 (STSW) - Body ground 10 to 14 V




OK

3.CHECK WIRE HARNESS (MAIN BODY ECU - ECM)

NG

4.CHECK WHETHER ENGINE STARTS
3.CHECK WIRE HARNESS (MAIN BODY ECU - ECM)
a.

Disconnect the G60 main body ECU connector.


b.

Disconnect the A7 ECM connector.


c.

Check the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G60-4 (STSW) - A7-14 (STSW) Below 1 Ω
G60-4 (STSW) or A7-14 (STSW) - Body ground 10 kΩ or higher




OK

4.CHECK WHETHER ENGINE STARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER ENGINE STARTS
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check that the engine starts normally.

OK:

Engine starts normally.




OK

END (SYSTEM OK)

NG