Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START C

2AZ-FE STARTING  PUSH-BUTTON START  B2285  Steering Lock Position Signal Circuit Malfunction  B2288  Steering Lock Signal Circuit Malfunction  


DESCRIPTION

The main body ECU and the steering lock ECU are connected by a cable and the LIN communication line. These DTCs are output when: 1) signals, transmitted through the cable and the communication line, do not match; or 2) a malfunction is detected in the circuit between the main body ECU and the steering lock ECU.

DTC No. DTC Detection Condition Trouble Area
B2285 Cable and LIN information between main body ECU and steering lock ECU are inconsistent
·

Main body ECU


·

Steering lock system


·

Wire harness


B2288 After turning engine switch from off to on (IG), steering wheel does not unlock for certain period of time (ECU unlocks steering wheel only when it receives unlock signal from LIN communication and cable)
·

Main body ECU


·

Steering lock system


·

Wire harness



WIRING DIAGRAM

A394001E01
1.083,1.125 1.604,1.344 0.521,0.219 10 false SLP1 1.604,2.146 2.125,2.365 0.521,0.219 10 false 5 0.344,2.76 0.865,2.979 0.521,0.219 10 false G32 0.354,2.927 1.708,3.219 1.354,0.292 10 false Steering Lock ECU 3.146,2.5 3.833,2.76 0.688,0.26 10 false LIN Line 5.677,2.802 6.74,3.052 1.063,0.25 10 false Main Body ECU 6.125,2.271 6.646,2.49 0.521,0.219 10 false LIN1 1.594,1.01 2.115,1.229 0.521,0.219 10 false 4 5.271,1.115 5.792,1.333 0.521,0.219 10 false G57 5.302,0.896 5.823,1.115 0.521,0.219 10 false 18 5.313,2.25 5.833,2.469 0.521,0.219 10 false 4A 5.323,2.031 5.844,2.25 0.521,0.219 10 false 20 1.219,2.271 1.74,2.49 0.521,0.219 10 false LIN 5.646,1.125 6.167,1.344 0.521,0.219 10 false SLP

PROCEDURE

1.READ VALUE USING GTS (STEERING LOCK CONDITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Main Body ECU / Data List / Str Unlock SW.


d.

Read the display on the tester.

Main body ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
Steering Unlock Switch Steering lock condition / ON or OFF ON: Steering is unlocked
OFF: Steering is locked
-


OK:

ON appears on the screen.




NG

2.CHECK WIRE HARNESS (MAIN BODY ECU - STEERING LOCK ECU)

OK

REPLACE MAIN BODY ECU

2.CHECK WIRE HARNESS (MAIN BODY ECU - STEERING LOCK ECU)
a.

Disconnect the G57 main body ECU connector.


b.

Disconnect the G32 steering lock ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G57-18 (SLP) - G32-4 (SLP1) Below 1 Ω
G57-18 (SLP) or G32-4 (SLP1) - Body ground 10 kΩ or higher




OK

3.CHECK WHETHER ENGINE STARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER ENGINE STARTS
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check that the engine starts normally.

OK:

Engine starts normally.




OK

END (MAIN BODY ECU IS FAULTY)

NG