Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START J

2AZ-FE STARTING  PUSH-BUTTON START  Engine Switch Indicator Circuit  


DESCRIPTION

Engine start conditions or system malfunctions can be checked by observing the status of the engine switch indicator light.

Engine switch indicator light condition
Power Source Mode/Condition Indicator Light Condition
Brake pedal released Brake pedal depressed, shift lever in P or N
Off OFF Illuminates (green)
On (ACC, IG) Illuminates (amber) Illuminates (green)
Engine running OFF OFF
Steering lock not unlocked Flashes (green) for 30 seconds Flashes (green) for 30 seconds
System malfunction Flashes (amber) for 15 seconds Flashes (amber) for 15 seconds
Stop light switch with shift lever in P or N malfunction Flashes (green) for 15 seconds Flashes (green) for 15 seconds

WIRING DIAGRAM

A393980E01
1.135,1.49 1.698,1.729 0.563,0.24 10 false INDS 1.094,2 1.656,2.24 0.563,0.24 10 false INDW 1.115,2.5 1.677,2.74 0.563,0.24 10 false SWIL 1.167,4.052 1.729,4.292 0.563,0.24 10 false GND 1.135,4.458 1.698,4.698 0.563,0.24 10 false COM 0.51,4.927 1.073,5.167 0.563,0.24 10 false G31 0.521,5.094 1.479,5.333 0.958,0.24 10 false Engine Switch 1.635,4.333 2.198,4.573 0.563,0.24 10 false 4 1.635,3.885 2.198,4.125 0.563,0.24 10 false 5 1.646,2.375 2.208,2.615 0.563,0.24 10 false 11 1.625,1.865 2.188,2.104 0.563,0.24 10 false 13 1.625,1.365 2.188,1.604 0.563,0.24 10 false 12 5.396,1.365 5.958,1.604 0.563,0.24 10 false 15 5.396,1.875 5.958,2.115 0.563,0.24 10 false 14 5.417,2.365 5.979,2.604 0.563,0.24 10 false 25 5.688,3.396 6.25,3.635 0.563,0.24 10 false G57 5.698,3.563 6.771,3.823 1.073,0.26 10 false Main Body ECU 5.74,2.49 6.302,2.729 0.563,0.24 10 false SWIL 5.729,2 6.292,2.24 0.563,0.24 10 false INDW 5.729,1.5 6.292,1.74 0.563,0.24 10 false INDS

PROCEDURE

1.INSPECT ENGINE SWITCH
A393973E04
0.5,0.833 1.375,1.094 true 0.667,1.823 1.156,1.5 true 1.604,1.854 1.458,1.521 true 2.146,1.875 1.708,1.521 true 1.708,1.083 2.823,0.938 true 0.396,1.844 0.875,2.104 0.479,0.26 10 false INDW 0.167,0.74 0.604,1 0.438,0.26 10 false GND 2.875,0.844 3.313,1.104 0.438,0.26 10 false COM 1.49,1.875 1.927,2.135 0.438,0.26 10 false INDS 2.052,1.885 2.49,2.146 0.438,0.26 10 false SWIL 0.083,0.094 0.563,0.354 0.479,0.26 10 false *a

a.

Remove the engine switch.


b.

Apply battery voltage between the terminals of the switch, and check the illumination condition of the engine switch indicator light.

NOTICE:
·

If the positive (+) lead and the negative (-) lead are incorrectly connected, the engine switch indicator light will not illuminate.

·

If the voltage is too low, the indicator light will not illuminate.



OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 11 (SWIL)
Battery negative (-) → Terminal 4 (COM) or 5 (GND)
Illuminates
Battery positive (+) → Terminal 12 (INDS)
Battery negative (-) → Terminal 4 (COM) or 5 (GND)
Illuminates
Battery positive (+) → Terminal 13 (INDW)
Battery negative (-) → Terminal 4 (COM) or 5 (GND)
Illuminates


Text in Illustration
*a Component without harness connected
(Engine Switch)



OK

2.CHECK WIRE HARNESS (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE ENGINE SWITCH

2.CHECK WIRE HARNESS (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the G31 engine switch connector.


b.

Disconnect the G57 main body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G31-11 (SWIL) - G57-25 (SWIL) Below 1 Ω
G31-12 (INDS) - G57-15 (INDS) Below 1 Ω
G31-13 (INDW) - G57-14 (INDW) Below 1 Ω
G31-5 (GND) - Body ground Below 1 Ω
G31-4 (COM) - Body ground Below 1 Ω
G31-11 (SWIL) or G57-25 (SWIL) - Body ground 10 kΩ or higher
G31-12 (INDS) or G57-15 (INDS) - Body ground 10 kΩ or higher
G31-13 (INDW) or G57-14 (INDW) - Body ground 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR