Home › Engine / Hybrid System › 2GR-FE CHARGING › GENERATOR
RM24M0E _51 Engine / Hybrid System _059577 2GR-FE CHARGING _0292086 GENERATOR A

2GR-FE CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27415 1.REMOVE GENERATOR CLUTCH PULLEY

a.
A395928

Using a screwdriver, remove the generator pulley cap.


b.
A128069E01
0.242,0.551 0.777,0.704 0.534,0.152 10 SST (A) 0.079,1.57 0.613,1.722 0.534,0.152 10 SST (B) 1.192,0.633 0.883,0.633 false 0.915,1.656 0.719,1.656 false

Set SST (A) and (B).

SST
09820-63020  


c.
U188441E02
2.458,3.208 1.906,3.208 false 2.083,2.802 1.792,2.896 false 1.479,0.333 0.917,0.271 false 2.115,2.729 2.688,2.906 0.573,0.177 10 false SST (A) 2.51,3.125 3.104,3.385 0.594,0.26 10 false SST (B) 0.313,0.167 0.875,0.365 0.563,0.198 10 false SST (A) 2.375,0.229 2.917,0.417 0.542,0.188 10 false SST (B)

Clamp SST (A) in a vise.

NOTICE:

Be sure to fix the flat surface of SST (A) in a vise.



d.
A135194E03
2.229,1.573 2.438,1.573 false 0.677,1.146 0.479,1.344 0.479,1.344 0.479,1.438 false 0.948,0.333 1.208,0.594 1.208,0.594 1.208,1.833 false 2.5,1.479 3.021,1.646 0.521,0.167 10 true SST (B) 0.198,1.469 0.719,1.635 0.521,0.167 10 false SST (A) 0.771,1.854 1.51,2 0.74,0.146 10 false Rotor Shaft

Place the rotor shaft end into SST (A).


e.
A135195E03
2.25,1.531 2.563,1.531 false 0.396,0.167 0.26,0.167 0.26,0.167 0.521,0.938 false 0.938,1.521 0.938,1.823 false 2.594,1.448 3.115,1.604 0.521,0.156 10 true SST (B) 0.448,0.073 1.281,0.229 0.833,0.156 10 false Clutch Pulley 0.625,1.844 1.146,2 0.521,0.156 10 false SST (B)

Fit SST (B) to the clutch pulley.


f.
A135196E03
2.219,1.563 2.479,1.563 false 2.542,1.469 3.135,1.688 0.594,0.219 10 true SST (B)

Loosen the pulley by turning SST (B) in the direction shown in the illustration.

NOTICE:

Hold the generator assembly tightly.



g.

Remove the generator assembly from SST.


h.

Remove the clutch pulley from the rotor shaft.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A135197

Place the generator assembly on the clutch pulley.


b.
A128071

Remove the 3 nuts and generator rear end cover.


Hide 27387B 3.REMOVE GENERATOR TERMINAL INSULATOR

a.
A128072

Remove the terminal insulator from the generator coil.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A128073

Remove the 2 screws and brush holder from the generator coil.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A128074

Remove the 4 bolts.


b.
A118275E01
1.115,0.436 1.430,0.586 0.315,0.150 10 SST 0.662,0.527 1.056,0.527 false 2.644,0.094 2.975,0.245 0.331,0.151 10 Turn 2.623,0.645 2.938,0.795 0.315,0.150 10 SST 2.149,0.737 2.556,0.737 false 0.645,1.736 0.976,1.887 0.331,0.151 10 Hold

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A377894

Remove the generator washer.


b.
A377895

Remove the generator rotor assembly.