Home › Engine / Hybrid System › 2GR-FE CHARGING › GENERATOR
RM24M0E _51 Engine / Hybrid System _059577 2GR-FE CHARGING _0292086 GENERATOR A

2GR-FE CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27330 1.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the drive end frame on the clutch pulley.


b.
A377895

Install the generator rotor assembly to the drive end frame.


c.
A377894

Place a new generator washer on the generator rotor.


Hide 27360 2.INSTALL GENERATOR COIL ASSEMBLY

a.
A128082E03
0.045,0.039 1.148,0.364 1.103,0.326 10 Deep Socket Wrench (21 mm) 1.673,0.614 1.389,0.236 false

Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.


b.
A128074

Install the 4 bolts.

Torque:
5.8 N*m (59 kgf*cm, 51 in.*lbf)


Hide 27370 3.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079315E48
0.948,0.51 0.854,0.156 0.854,0.156 2.479,0.76 false 0.542,0.052 0.792,0.219 0.25,0.167 10 false Pin

While pushing the 2 brushes into the generator brush holder assembly, insert a φ1.0 mm (0.039 in.) pin into the brush holder hole.


b.
A079316E16
1.656,1 1.615,1.188 false 1.458,1.198 1.906,1.375 0.448,0.177 10 false Pin

Install the brush holder assembly to the generator coil with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder.


Hide 27387B 4.INSTALL GENERATOR TERMINAL INSULATOR

a.
A384555

Install the terminal insulator to the generator coil.

NOTICE:

Pay attention to installation direction of the terminal insulator.



Hide 27039 5.INSTALL GENERATOR REAR END COVER

a.
A128071

Install the generator rear end cover to the generator coil with the 3 nuts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 6.INSTALL GENERATOR CLUTCH PULLEY

a.

Temporarily install the clutch pulley onto the rotor shaft.


b.
A128084E01
0.234,0.577 0.751,0.737 0.517,0.159 10 SST (A) 0.058,1.643 0.575,1.802 0.517,0.159 10 SST (B) 1.192,0.672 0.878,0.672 false 0.909,1.737 0.694,1.737 false

Set SST (A) and (B).

SST
09820-63020  


c.
U188441E02
2.458,3.208 1.906,3.208 false 2.083,2.802 1.792,2.896 false 1.479,0.333 0.917,0.271 false 2.115,2.729 2.688,2.906 0.573,0.177 10 false SST (A) 2.51,3.125 3.104,3.385 0.594,0.26 10 false SST (B) 0.313,0.167 0.875,0.365 0.563,0.198 10 false SST (A) 2.375,0.229 2.917,0.417 0.542,0.188 10 false SST (B)

Clamp SST (A) in a vise.

NOTICE:

Be sure to fix the flat surface of SST (A) in a vise.



d.
A135194E03
2.229,1.573 2.438,1.573 false 0.677,1.146 0.479,1.344 0.479,1.344 0.479,1.438 false 0.948,0.333 1.208,0.594 1.208,0.594 1.208,1.833 false 2.5,1.479 3.021,1.646 0.521,0.167 10 true SST (B) 0.198,1.469 0.719,1.635 0.521,0.167 10 false SST (A) 0.771,1.854 1.51,2 0.74,0.146 10 false Rotor Shaft

Place the rotor shaft end into SST (A).


e.
A135195E03
2.25,1.531 2.563,1.531 false 0.396,0.167 0.26,0.167 0.26,0.167 0.521,0.938 false 0.938,1.521 0.938,1.823 false 2.594,1.448 3.115,1.604 0.521,0.156 10 true SST (B) 0.448,0.073 1.281,0.229 0.833,0.156 10 false Clutch Pulley 0.625,1.844 1.146,2 0.521,0.156 10 false SST (B)

Fit SST (B) to the clutch pulley.


f.
A151433E01
0.126,1.511 1.151,1.705 1.025,0.195 10 Fulcrum Length 1.757,2.177 2.277,2.349 0.520,0.172 10 SST (B) 2.028,1.566 2.028,2.161 false

Tighten the pulley by turning SST (B) in the direction shown in the illustration.

Torque:
without SST : 110 N*m (1125 kgf*cm, 81 ft.*lbf)
with SST : 84 N*m (857 kgf*cm, 62 ft.*lbf)

NOTICE:
·

Use a torque wrench with a fulcrum length of 318 mm (12.52 in.).

·

This torque value is effective when SST is parallel to a torque wrench.

·

Hold the generator assembly tightly.




g.

Remove the generator assembly from SST.


h.

Check that the clutch pulley rotates smoothly.


i.

Install a new clutch pulley cap to the clutch pulley.