Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL PUMP
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292089 OIL PUMP G

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  INSPECTION  


PROCEDURE

Hide 1.INSPECT OIL PUMP ASSEMBLY

a.
D009205

Turn the drive gear with 2 screwdrivers and make sure it rotates smoothly.

NOTICE:

Be careful not to damage the oil seal lip.



Hide 2.INSPECT CLEARANCE OF OIL PUMP ASSEMBLY

a.
D009207

Push the driven gear to one side of the body. Using a feeler gauge, measure the clearance.

Standard body clearance:

0.10 to 0.17 mm (0.0039 to 0.0067 in.)


Maximum body clearance:

0.17 mm (0.0067 in.)


If the body clearance is greater than the maximum, replace the oil pump body sub-assembly.


b.
D009208

Measure the tip clearance between the driven gear teeth and drive gear teeth.

Standard tip clearance:

0.07 to 0.15 mm (0.0028 to 0.0059 in.)


Maximum tip clearance:

0.15 mm (0.0059 in.)


If the tip clearance is greater than the maximum, replace the oil pump body sub-assembly.


c.
D009209

Using a straightedge and feeler gauge, measure the side clearance of both gears.

Standard side clearance:

0.02 to 0.05 mm (0.0008 to 0.0020 in.)


Maximum side clearance:

0.05 mm (0.0020 in.)


Standard drive gear thickness:
Mark Thickness
1 10.690 to 10.699 mm (0.4209 to 0.4212 in.)
2 10.700 to 10.709 mm (0.4213 to 0.4216 in.)
3 10.710 to 10.720 mm (0.4217 to 0.4220 in.)
4 10.721 to 10.730 mm (0.4221 to 0.4224 in.)
5 10.731 to 10.740 mm (0.4225 to 0.4228 in.)

Standard driven gear thickness:
Mark Thickness
1 10.690 to 10.699 mm (0.4209 to 0.4212 in.)
2 10.700 to 10.709 mm (0.4213 to 0.4216 in.)
3 10.710 to 10.720 mm (0.4217 to 0.4220 in.)
4 10.721 to 10.730 mm (0.4221 to 0.4224 in.)
5 10.731 to 10.740 mm (0.4225 to 0.4228 in.)



Hide 35035 3.INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY

a.
D003648

Using a caliper gauge, measure the inside diameter of the oil pump body bush.

Standard inside diameter:

38.11 to 38.14 mm (1.5005 to 1.5015 in.)


Maximum inside diameter:

38.19 mm (1.5035 in.)


If the inside diameter is greater than the maximum, replace the oil pump body sub-assembly.


Hide 35370 4.INSPECT STATOR SHAFT ASSEMBLY

a.
D003653

Using a caliper gauge, measure the inside diameter of the stator shaft bushes.

Standard inside diameter:

20.50 to 21.53 mm (0.8465 to 0.8475 in.)


Maximum inside diameter:

21.57 mm (0.8492 in.)


If the inside diameter is greater than the maximum, replace the stator shaft assembly.