Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › UNDERDRIVE PLANETARY GEAR
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292093 UNDERDRIVE PLANETARY GEAR A

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  UNDERDRIVE PLANETARY GEAR  REASSEMBLY  


PROCEDURE

Hide 34341 1.INSTALL UNDERDRIVE PLANETARY RING GEAR

a.
D008112

Install a new snap ring to the outer race of the tapered roller bearing.


b.
D008113

Using a piston ring compressor, squeeze the snap ring.


c.
D008114E04
0.104,2 0.25,2.125 0.146,0.125 2.615,0.427 2.979,0.708 0.365,0.281 10 false SST 1.781,0.167 2.146,0.448 0.365,0.281 10 false SST

Using SST a press, press in the outer race of the tapered roller bearing.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07100)


d.
D003827

Install the underdrive planetary ring gear to the counter driven gear.


e.
D003826

Using snap ring pliers, install the snap ring.


Hide 34330 2.INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
D003692

Using a press, install the tapered roller bearing.


b.
D008117

Install the counter driven gear with planetary ring gear to the underdrive planetary gear.


c.
D008118E04
0.208,0.469 0.521,0.625 0.313,0.156 10 false SST 2.823,0.427 3.135,0.583 0.313,0.156 10 false SST

Using SST and a press, press in the tapered roller bearing.

SST
09316-60011  (09316-00011)

NOTICE:

Press in the counter driven gear while rotating it.



d.
D003694

Using a press, press in the parking lock gear.

NOTICE:

Press in the counter driven gear while rotating it.



e.
D008120E05
0.271,0.906 0.604,1.063 0.333,0.156 10 false SST

Using SST and a press, press in the differential drive pinion.

NOTICE:

Press in the counter driven gear while rotating it.


SST
09506-35010  
09950-60010  (09951-00250)


f.
D008121E05
0.208,0.708 0.542,0.865 0.333,0.156 10 false SST

Using SST and a press, press in the cylindrical roller bearing inner race.

NOTICE:

Press in the counter driven gear while rotating it.


SST
09506-35010  
09950-60010  (09951-00250)


g.
D025609E14
1.948,1.052 2.573,0.469 true 2.604,0.333 2.927,0.5 0.323,0.167 10 false SST

Clamp the underdrive planetary gear in a soft jaw vise.

NOTICE:

Be careful not to damage the differential drive pinion.



h.

Using SST, install a new lock nut.

T = 280 N*m{ 2,855 kgf*cm 207 ft.*lbf }

SST
09564-16020  

HINT:

Use a torque wrench with a fulcrum length of 750 mm (29.53 in.)



i.
D025594E08
1.802,0.583 2.625,1.177 2.625,1.177 2.063,1.635 false 2.688,1.094 2.979,1.25 0.292,0.156 10 false SST

Using SST and a torque wrench, measure the turning torque of underdrive planetary gear assembly while rotating the torque wrench at 60 rpm.

SST
09564-16020  
09387-00050  

Torque:
Standard turning torque at 60 rpm : 0.23 to 5.01 N*m (2 to 51 kgf*cm, 2.0 to 44.3 in.*lbf)

HINT:

Use a torque wrench with a fulcrum length of 160 mm (6.30 in.).



j.
D003852

Using a pin punch and hammer, stake the lock nut.

NOTICE:

Make sure that there are no cracks on the nut.