Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › UNDERDRIVE CLUTCH
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292094 UNDERDRIVE CLUTCH A

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  UNDERDRIVE CLUTCH  REASSEMBLY  


PROCEDURE

Hide 34204A 1.INSTALL UNDERDRIVE CLUTCH DRUM O-RING

a.
D004078

Coat a new O-ring with ATF and install it to the underdrive clutch drum.


Hide 34205B 2.INSTALL UNDERDRIVE CLUTCH PISTON SET

a.
D003860

Coat the underdrive clutch piston with ATF, and install it to the underdrive clutch piston drum.

NOTICE:

Be careful not to damage the O-ring.



b.
D003704

Install the piston return spring and clutch balancer to the underdrive clutch drum.

NOTICE:

Be careful not to damage the lip seal of the clutch balancer.



c.
D003703E10
2.49,0.51 2.896,0.333 false 2.948,0.208 3.26,0.396 0.313,0.188 10 false SST

Place SST on the clutch balancer and compress the piston return spring with a press.

SST
09350-32014  (09351-32070)


d.

Using a snap ring expander, install the snap ring to underdrive clutch drum.

NOTICE:
·

Be sure the end gap of the snap ring is not aligned with the clutch balancer's claw.

·

Stop the press when the spring sheet is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the sap ring groove.

·

This prevents the spring sheet from being deformed.

·

Do not expand the snap ring excessively.




Hide 34261 3.INSTALL NO. 1 UNDERDRIVE CLUTCH DISC

a.
C129394E06
2.719,0.427 3.073,0.292 false 2.708,0.594 3.073,0.479 false 2.719,0.708 3.063,0.635 false 2.708,0.833 3.063,0.823 false 2.719,0.948 3.063,0.969 false 2.708,1.063 3.073,1.146 false 2.708,1.229 3.052,1.375 false 3.115,0.198 3.292,0.354 0.177,0.156 10 false F 3.115,0.385 3.292,0.542 0.177,0.156 10 false D 3.104,0.563 3.281,0.719 0.177,0.156 10 false P 3.115,1.083 3.292,1.24 0.177,0.156 10 false D 3.094,1.323 3.271,1.479 0.177,0.156 10 false P 3.104,0.74 3.281,0.896 0.177,0.156 10 false D 3.115,0.906 3.292,1.063 0.177,0.156 10 false P

Install the 3 plates, 3 discs and flange.

Install in order:

P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange



b.
D008125

Using a screwdriver, install the snap ring.


c.

Check that the end gap of the snap ring is not aligned with one of the cutouts.


Hide 4.INSPECT UNDERDRIVE PACK CLEARANCE

a.

Install the underdrive clutch to the transaxle case.

NOTICE:

Be careful not to damage the oil seal rings.



b.
D008123

Set a dial indicator as shown in the illustration.


c.
D008124

Measure the underdrive clutch piston stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

Standard pack clearance:

1.51 to 1.90 mm (0.0594 to 0.0748 in.)


If the pack clearance is less than the minimum, parts may have been assembled incorrectly, so check and reassemble again.

If the park clearance is not as specified, select another flange.

HINT:

There are 3 flanges in different thickness.


Standard flange thickness:
No. Thickness No. Thickness
A 3.0 mm (0.118 in.) C 3.4 mm (0.134 in.)
B 3.2 mm (0.126 in.) - -