Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292095 DIFFERENTIAL CASE A

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331F 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C083137

Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF, and install them to the differential case.


Hide 41342F 2.INSTALL NO. 1 FRONT DIFFERENTIAL PINION SHAFT

a.
C083135

Coat the front differential pinion shaft with ATF, and install it to the differential case.


Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C060005

Using a pin punch and hammer, tap in the pinion shaft straight pin.


b.
C060006

Using a chisel and hammer, stake the differential case.


Hide 41311F 5.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
D025218E07
1.698,0.667 2.458,1.333 2.458,1.333 1.688,1.844 true 2.51,1.25 2.802,1.427 0.292,0.177 10 false SST

Using SST and a press, press in the front differential case tapered roller bearing rear inner race to the differential case.

SST
09608-06041  


b.
D025219E08
1.25,1.5 0.5,0.396 0.5,0.396 1.344,0.844 true 0.198,0.292 0.521,0.469 0.323,0.177 10 false SST

Using SST and a hammer, tap in the case washer and front differential case tapered roller bearing rear outer race to the transaxle case.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
D025216E06
1.781,0.844 2.063,0.844 false 2.104,0.76 2.396,0.938 0.292,0.177 10 false SST

Using SST and a press, press in the front differential case tapered roller bearing front inner race to the differential case.

SST
09608-06041  


b.
D025217E06
1.271,0.885 0.854,0.552 0.854,0.552 1.167,1.469 true 0.552,0.417 0.844,0.594 0.292,0.177 10 false SST

Using SST and a hammer, tap in the front differential case tapered roller bearing front outer race to the transaxle housing.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07100)
09950-60010  (09951-00340)


Hide 41221 7.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215E21
1.094,0.052 1.885,0.24 0.792,0.188 10 false 90 to 110°C

Using ATF and heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).


b.

Clean the contact surface of the front differential case.


c.
C083132E11
1.76,1.521 0.896,1.865 0.896,1.865 1.76,1.625 true 0.177,1.781 1,1.938 0.823,0.156 10 false Matchmark

Align the matchmarks, and install the front differential ring gear case quickly.


d.
C083133

Tighten the 10 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 8.INSPECT TAPERED ROLLER BEARING PRELOAD

a.
C083139

Install the differential assembly to the transaxle case.


b.

Install the transaxle housing to the transaxle case.


c.
C050259E03
0.458,1.073 0.25,0.49 0.25,0.49 0.885,0.49 false 0.698,0.708 0.25,0.5 false 1.125,0.25 0.698,0.167 false 1.448,0.271 1.208,0.531 false 0.458,1.646 0.302,1.906 0.302,1.906 0.75,1.948 false 1.25,1.958 1.333,2.042 false 1.594,1.604 1.531,1.406 1.531,1.406 1.823,1.594 false 2.146,1.594 2.281,1.667 2.281,1.667 2.281,1.552 false 2.531,1.135 2.677,1.188 false 2.5,0.792 2.615,0.865 false 1.875,0.479 1.792,0.594 1.792,0.594 2.125,0.563 false 1.438,1.229 1.563,1.385 0.125,0.156 10 true A 2.26,1.688 2.385,1.844 0.125,0.156 10 false A 2.729,1.115 2.854,1.271 0.125,0.156 10 false A 1.656,0.521 1.781,0.677 0.125,0.156 10 false B 2.656,0.813 2.781,0.969 0.125,0.156 10 false B 1.073,0.458 1.198,0.615 0.125,0.156 10 false B 0.552,0.073 0.677,0.229 0.125,0.156 10 false C 0.115,0.396 0.24,0.552 0.125,0.156 10 false C 0.156,1.833 0.281,1.99 0.125,0.156 10 false C 1.365,1.979 1.49,2.135 0.125,0.156 10 false C

Install the 16 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

for bolt A

29 N*m (296 kgf*cm, 21 ft.*lbf)

for bolt B and C


HINT:

Each bolt length is indicated below.


Bolt length:

50 mm (1.97 in.) for bolt A and B

42 mm (1.65 in.) for bolt C



d.
C083572E06
1.813,1.667 2.167,1.469 false 2.198,1.375 2.5,1.531 0.302,0.156 10 false SST

Using SST, turn the differential.

SST
09564-32011  


e.
C083572E06
1.813,1.667 2.167,1.469 false 2.198,1.375 2.5,1.531 0.302,0.156 10 false SST

Using SST and torque wrench, measure the preload of the differential.

SST
09564-32011  

Torque:
Standard turning torque at 60 rpm : 0.20 to 0.69 N*m (2.0 to 7.0 kgf*cm, 1.8 to 6.1 in.*lbf)

for new

0.10 to 0.35 N*m (1.0 to 3.6 kgf*cm, 0.9 to 3.1 in.*lbf)

for used


Standard adjusting shim thickness:
Mark Thickness
0 1.90 mm (0.074 in.)
1 1.95 mm (0.077 in.)
2 2.00 mm (0.079 in.)
3 2.05 mm (0.081 in.)
4 2.10 mm (0.083 in.)
5 2.15 mm (0.085 in.)
6 2.20 mm (0.087 in.)
7 2.25 mm (0.089 in.)
8 2.30 mm (0.091 in.)
9 2.35 mm (0.093 in.)
A 2.40 mm (0.094 in.)
B 2.45 mm (0.096 in.)
C 2.50 mm (0.098 in.)
D 2.55 mm (0.100 in.)
E 2.60 mm (0.102 in.)
F 2.65 mm (0.104 in.)
G 2.70 mm (0.106 in.)
H 2.75 mm (0.108 in.)
J 2.80 mm (0.110 in.)



f.
D009182

Remove the 16 bolts.


g.

Using a plastic-faced hammer, remove the transaxle housing.


h.
C083139

Remove the differential.


Hide 35111D 9.INSTALL TRANSAXLE HOUSING OIL SEAL

D025606E05
1.115,0.958 1.396,0.823 false 1.24,1.406 1.396,0.823 false 1.438,0.708 1.813,0.917 0.375,0.208 10 false SST

a.

Coat the lip of a new oil seal with a little amount of MP grease.


b.

Using SST and a hammer, tap in the oil seal.

SST
09350-32014  (09351-32150)
09950-70010  (09951-07150)


Hide 41141H 10.INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

D025605E05
2.083,1 2.927,1.219 2.927,1.219 2.188,1.333 true 2.969,1.146 3.281,1.313 0.313,0.167 10 false SST

a.

Coat the lip of a new oil seal with a little amount of MP grease.


b.

Using SST and a hammer, tap in the oil seal.

SST
09350-32014  (09351-32150)
09950-70010  (09951-07150)