Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0717  Input Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the turbine, which shows the input revolution of the transaxle. By comparing the input speed signal (NT) with the counter gear speed sensor signal (NC), the ECM detects the shift timing of the gears and controls the engine torque and hydraulic pressure according to various conditions. As a result, smooth gear shifting is achieved.

DTC No. DTC Detection Condition Trouble Area
P0717 ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more (1 trip detection logic):
(a) Vehicle speed: 50 km/h (31 mph) or more
(b) Park/Neutral position switch (NSW, R and L) is OFF
(c) Speed sensor NT: Less than 300 rpm
·

Open or short in speed sensor NT circuit

·

Speed sensor NT

·

ECM



MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (input speed sensor) or is output only a little. The NT terminal of the ECM detects the revolving signal from the speed sensor (NT) (input RPM). The ECM outputs a gear shift signal comparing the input speed sensor (NT) with the output speed sensor (NC).

While the vehicle is operating in the 2nd, 3rd or O/D gear position with the shift lever on D, if the input shaft revolution is less than 300 rpm*1 and the output shaft revolution is 1,000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is approximately 50 km/h (31 mph) or more.


WIRING DIAGRAM

C142134E09
5.667,0.667 6.146,0.875 0.479,0.208 10 false NT+ 5.948,2.188 6.427,2.396 0.479,0.208 10 false ECM 5.333,0.667 5.563,0.875 0.229,0.208 10 false D2 5.333,1.656 5.563,1.865 0.229,0.208 10 false D2 5.656,1.667 6.135,1.875 0.479,0.208 10 false NT- 5.302,0.438 5.781,0.646 0.479,0.208 10 false 125 5.302,1.427 5.781,1.635 0.479,0.208 10 false 124 0.906,1.083 3.167,1.552 2.26,0.469 10 false Input Speed Sensor NT (Transmission Revolution Sensor NT) 0.906,0.906 1.271,1.094 0.365,0.188 10 false D60 1.865,0.771 2.229,0.958 0.365,0.188 10 false 2 1.271,0.76 1.635,0.948 0.365,0.188 10 false 1

CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch on (IG) and turn the tester ON.

5.

Enter the following menus: Powertrain / Engine and ECT / Data List.

6.

Follow the instructions on the tester and read the Data List.


ECM:
Item Measurement Item/
Range (Display)
Normal Condition Diagnostic Note
SPD (NT) Input turbine speed/
Min.: 0 rpm
Max.: 12,750 rpm
·

Lock-up ON (after warming up engine):

Input turbine speed (NT) is equal to engine speed.

·

Lock-up OFF (idling with shift lever on N):

Input turbine speed (NT) is nearly equal to engine speed.


Data is displayed in increments of 50 rpm

HINT:
·

SPD (NT) is always 0 rpm while driving:

Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 rpm and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:

Sensor trouble, improper installation, or intermittent connection trouble of the circuit.



PROCEDURE

1.INSPECT SPEED SENSOR (INSTALLATION)
a.
C140845E02
0.625,1.729 0.948,1.938 0.323,0.208 10 false OK 2.563,1.74 2.885,1.948 0.323,0.208 10 false NG 1.646,1.49 2.354,1.698 0.708,0.208 10 false Clearance

Check the speed sensor NT installation.

OK:

Installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.




OK

2.INSPECT SPEED SENSOR NT

NG

SECURELY INSTALL SENSOR OR REPLACE SPEED SENSOR

2.INSPECT SPEED SENSOR NT
a.

Disconnect the D60 sensor connector from the transaxle.


C140846E02
1.198,1.75 1.49,1.208 false 2.25,1.75 1.958,1.208 false 1.115,1.75 1.469,1.958 0.354,0.208 10 false 2 2.271,1.74 2.625,1.958 0.354,0.219 10 false 1

b.

Measure the resistance of the sensor.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω




OK

3.CHECK WIRE HARNESS (SPEED SENSOR - ECM)

NG

REPLACE SPEED SENSOR NT

3.CHECK WIRE HARNESS (SPEED SENSOR - ECM)
a.
U189335E02
1.74,2.146 1.5,2.656 true 1.823,2.146 2.063,2.656 true 1.563,0.896 1.938,1.125 0.375,0.229 10 false D2 1.406,2.688 1.698,2.885 0.292,0.198 10 false NT- 2,2.688 2.406,2.885 0.406,0.198 10 false NT+ 0.115,0.073 1.469,0.24 1.354,0.167 10 false Wire Harness Side:

Disconnect the D2 ECM connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
D2-125 (NT+) - D2-124 (NT-) 20°C (68°F) 560 to 680 Ω
D2-125 (NT+) - Body ground 20°C (68°F) 10 kΩ or higher
D2-124 (NT-) - Body ground 20°C (68°F) 10 kΩ or higher




OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR