Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0793  Intermediate Shaft Speed Sensor "A"  


DESCRIPTION

This sensor detects the rotation speed of the counter gear. By comparing the counter gear speed signal (NC) with the direct clutch speed sensor signal (NT), the ECM detects the shift timing of the gears and approximately controls the engine torque and hydraulic pressure according to various conditions. Thus smooth gear shifting is performed.

DTC No. DTC Detection Condition Trouble Area
P0793 ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more (1 trip detection logic):
(a) Vehicle speed: 50 km/h (31 mph) or more
(b) Park/Neutral position switch (NSW) is OFF
(c) Speed sensor NC: Less than 300 rpm
·

Open or short in speed sensor NC circuit

·

Speed sensor NC

·

ECM



MONITOR DESCRIPTION

The NC terminal of the ECM detects revolution signals from the speed sensor NC (counter gear rpm). The ECM calculates gear shifts by comparing the speed sensor NT with the speed sensor NC.

While the vehicle is operating in the 2nd, 3rd or O/D gear position with the shift lever on D, if the counter gear revolution is less than 300 rpm*1 and the output shaft revolution is more than 1,000 rpm*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C142134E10
5.667,0.667 6.146,0.875 0.479,0.208 10 false NC+ 5.938,2.198 6.417,2.406 0.479,0.208 10 false ECM 5.333,0.667 5.563,0.875 0.229,0.208 10 false D2 5.333,1.656 5.563,1.865 0.229,0.208 10 false D2 5.667,1.656 6.146,1.865 0.479,0.208 10 false NC- 5.302,0.448 5.781,0.656 0.479,0.208 10 false 101 5.292,1.438 5.771,1.646 0.479,0.208 10 false 102 1.052,1.177 2.292,1.385 1.24,0.208 10 false Speed Sensor NC 1.052,0.99 1.417,1.177 0.365,0.188 10 false D58 1.885,0.781 2.25,0.969 0.365,0.188 10 false 2 1.26,0.771 1.625,0.958 0.365,0.188 10 false 1

CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch on (IG) and turn the tester ON.

5.

Enter the following menus: Powertrain / Engine and ECT / Data List.

6.

Follow the instructions on the tester and read the Data List.


ECM:
Item Measurement Item/ Range (Display) Normal Condition Diagnostic Note
SPD (NC) Counter gear speed/
Min.: 0 rpm
Max.: 12,750 rpm
4th (O/D) gear when shift lever is on D (after warming up the engine);
Intermediate shaft speed (NC) becomes close to the engine speed
Data is displayed in increments of 50 rpm

HINT:
·

SPD (NC) is always 0 rpm while driving:

Open or short in the sensor or circuit.

·

SPD (NC) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:

Sensor trouble, improper installation, or intermittent connection trouble of the circuit.



PROCEDURE

1.INSPECT SPEED SENSOR (INSTALLATION)
C140845E02
0.625,1.729 0.948,1.938 0.323,0.208 10 false OK 2.563,1.74 2.885,1.948 0.323,0.208 10 false NG 1.646,1.49 2.354,1.698 0.708,0.208 10 false Clearance

a.

Check the speed sensor NC installation.

OK:

Installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.




OK

2.INSPECT SPEED SENSOR NC

NG

REPLACE SPEED SENSOR NC

2.INSPECT SPEED SENSOR NC
C140846E02
1.198,1.75 1.49,1.208 false 2.25,1.75 1.958,1.208 false 1.115,1.75 1.469,1.958 0.354,0.208 10 false 2 2.271,1.74 2.625,1.958 0.354,0.219 10 false 1

a.

Disconnect the D58 sensor connector from the transaxle.


b.

Measure the resistance of the sensor.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω


OK:

Valve moves and makes operating noise.




OK

3.CHECK WIRE HARNESS (SPEED SENSOR - ECM)

NG

REPLACE SPEED SENSOR NC

3.CHECK WIRE HARNESS (SPEED SENSOR - ECM)
U189340E02
1.74,2.052 1.51,2.615 true 1.823,2.052 2.063,2.615 true 1.563,0.927 1.938,1.156 0.375,0.229 10 false D2 2,2.635 2.406,2.833 0.406,0.198 10 false NC- 1.354,2.635 1.76,2.833 0.406,0.198 10 false NC+ 0.146,0.104 1.531,0.271 1.385,0.167 10 false Wire Harness Side:

a.

Disconnect the D2 ECM connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
D2-101 (NC+) - D2-102 (NC-) 560 to 680 Ω
D2-101 (NC+) - Body ground 10 kΩ or higher
D2-102 (NC-) - Body ground 10 kΩ or higher




OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR