Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2014.09–2016.05
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0705 When one of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic)
·

P input signal is ON

·

N input signal is ON

·

R input signal is ON

·

D input signal is ON


(B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic)
·

STAR input signal is ON

·

R input signal is ON

·

D input signal is ON


(C) When any of following conditions is for 2 sec. or more in the S position (2 trip detection logic)
·

STAR input signal is ON

·

P input signal is ON

·

N input signal is ON

·

R input signal is ON


(D) All of the following signals are OFF simultaneously (2 trip detection logic)*
·

STAR input signal is OFF

·

P input signal is OFF

·

N input signal is OFF

·

R input signal is OFF

·

D input signal is OFF


·

Open or short in park/neutral position switch circuit

·

Park/Neutral position switch

·

ECM



HINT:

*: Only for Euro-OBD vehicle


MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is on P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N or D).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C142132E03
6.344,4.292 6.74,4.479 0.396,0.188 10 false ECM 5.865,0.813 6.115,1 0.25,0.188 10 false D2 5.865,1.281 6.115,1.469 0.25,0.188 10 false D2 5.865,1.896 6.115,2.083 0.25,0.188 10 false D2 5.865,2.354 6.115,2.542 0.25,0.188 10 false D2 5.875,0.625 6.271,0.813 0.396,0.188 10 false 73 5.875,1.073 6.271,1.26 0.396,0.188 10 false 54 5.865,1.677 6.26,1.865 0.396,0.188 10 false 53 5.865,2.146 6.26,2.333 0.396,0.188 10 false 56 6.208,0.813 6.698,1 0.49,0.188 10 false P 6.198,1.281 6.688,1.469 0.49,0.188 10 false N 6.198,1.885 6.688,2.073 0.49,0.188 10 false R 6.198,2.354 6.688,2.542 0.49,0.188 10 false D 5.865,3.76 6.115,3.948 0.25,0.188 10 false D2 5.865,3.542 6.26,3.729 0.396,0.188 10 false 74 6.198,3.75 6.688,3.938 0.49,0.188 10 false S 3.594,0.927 3.802,1.115 0.208,0.188 10 false PL 3.906,0.927 4.115,1.115 0.208,0.188 10 false 6 3.906,1.385 4.115,1.573 0.208,0.188 10 false 9 3.906,1.99 4.115,2.177 0.208,0.188 10 false 1 3.906,2.458 4.115,2.646 0.208,0.188 10 false 7 2.688,1.698 2.896,1.885 0.208,0.188 10 false 2 2.438,2.99 4.281,3.177 1.844,0.188 10 false Park/Neutral Position Switch 2.438,2.792 2.781,2.979 0.344,0.188 10 false D4 2.438,4.271 4.281,4.458 1.844,0.188 10 false Transmission Control Switch 2.438,4.094 2.781,4.281 0.344,0.188 10 false G9 3.604,1.396 3.813,1.583 0.208,0.188 10 false NL 3.604,2 3.813,2.188 0.208,0.188 10 false RL 2.917,1.698 3.125,1.885 0.208,0.188 10 false RB 3.604,2.458 3.813,2.646 0.208,0.188 10 false DL 3.885,3.865 4.094,4.052 0.208,0.188 10 false 13 2.698,3.875 2.906,4.063 0.208,0.188 10 false 6 3.677,3.865 3.885,4.052 0.208,0.188 10 false S 2.896,3.865 3.104,4.052 0.208,0.188 10 false IG 1.042,1.583 1.896,1.771 0.854,0.188 10 false from Battery 1.021,3.75 1.875,3.938 0.854,0.188 10 false from Battery

C267906E02
5.698,2.604 6.094,2.813 0.396,0.208 10 false D2 4.448,2.792 4.615,3 0.167,0.208 10 false 3 4.76,2.802 4.927,3.01 0.167,0.208 10 false 2 4.438,3.625 4.604,3.833 0.167,0.208 10 false 5 3.104,4.281 3.271,4.49 0.167,0.208 10 false 5 3.281,4.281 3.448,4.49 0.167,0.208 10 false L 3.677,4.281 3.844,4.49 0.167,0.208 10 false B 3.885,4.271 4.052,4.479 0.167,0.208 10 false 4 3.5,5.635 3.667,5.844 0.167,0.208 10 false 3 2.729,5.646 2.896,5.854 0.167,0.208 10 false 5 3.5,5.323 3.667,5.531 0.167,0.208 10 false 2 2.729,5.333 2.896,5.542 0.167,0.208 10 false 1 4.75,3.625 4.917,3.833 0.167,0.208 10 false 1 4.958,3.219 5.479,3.427 0.521,0.208 10 false ST CUT 6.021,2.594 6.604,2.802 0.583,0.208 10 false STAR 5.708,2.375 6.104,2.583 0.396,0.208 10 false 52 2.323,2.229 2.719,2.438 0.396,0.208 10 false G58 1.917,2.229 2.313,2.438 0.396,0.208 10 false IG2D 1.896,2.719 2.292,2.927 0.396,0.208 10 false STR2 1.938,3.698 2.281,3.906 0.344,0.208 10 false STR 1.5,2.719 1.896,2.927 0.396,0.208 10 false AM1 1.51,3.708 1.906,3.917 0.396,0.208 10 false AM2 2.365,2.01 2.76,2.219 0.396,0.208 10 false 11 3.729,1.781 4.125,1.99 0.396,0.208 10 false IG2 4.188,1.229 4.583,1.438 0.396,0.208 10 false 3 4.188,1.563 4.583,1.771 0.396,0.208 10 false 1 3.396,1.229 3.792,1.438 0.396,0.208 10 false 5 3.396,1.563 3.792,1.771 0.396,0.208 10 false 2 2.313,2.719 2.708,2.927 0.396,0.208 10 false G60 2.406,2.49 2.802,2.698 0.396,0.208 10 false 6 2.323,3.719 2.719,3.927 0.396,0.208 10 false G57 1.406,4.125 2.448,4.333 1.042,0.208 10 false Main Body ECU 2.76,4.406 3.802,4.615 1.042,0.208 10 false D4 4.042,5.729 4.625,5.938 0.583,0.208 10 false Starter 2.76,4.573 4.688,4.781 1.927,0.208 10 false Park/Neutral Position Switch 0.156,3.938 1,4.146 0.844,0.208 10 false from Battery 0.948,5.51 1.792,5.719 0.844,0.208 10 false from Battery 0.156,2.896 1,3.104 0.844,0.208 10 false from Battery 1.719,1.115 2.563,1.323 0.844,0.208 10 false from Battery 2.406,3.49 2.802,3.698 0.396,0.208 10 false 8 1.146,2.719 1.542,2.927 0.396,0.208 10 false G57 1.229,2.49 1.625,2.698 0.396,0.208 10 false 6 1.146,3.719 1.542,3.927 0.396,0.208 10 false G58 1.219,3.49 1.615,3.698 0.396,0.208 10 false 1 5.698,4.844 6.094,5.052 0.396,0.208 10 false A7 6.031,4.823 6.615,5.031 0.583,0.208 10 false STA 5.698,4.615 6.094,4.823 0.396,0.208 10 false 48 6.156,7.927 6.552,8.135 0.396,0.208 10 false ECM 3.063,5.865 3.458,6.073 0.396,0.208 10 false ST

CAUTION / NOTICE / HINT

HINT:

Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch on (IG) and turn the tester ON.

5.

Enter the following menus: Powertrain / Engine and ECT / Data List.

6.

Follow the instructions on the tester and read the Data List.

ECM:
Item Measurement Item/
Range (Display)
Normal Condition Diagnostic Note
Neutral Position Switch Signal PNP switch status/
ON or OFF
Shift lever is:
On P or N: ON
Not on P or N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF


-
Shift status ECM gear shift command/
1st, 2nd, 3rd or 4th
Shift lever position is:
On D: 1st, 2nd, 3rd or 4th
-
Shift switch status (R range) PNP switch status/
ON or OFF
Shift lever is:
On R: ON
Not on R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (P range) PNP switch status/
ON or OFF
Shift lever is:
On P: ON
Not on P: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (N range) PNP switch status/
ON or OFF
Shift lever is:
On N: ON
Not on N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift switch status (D range) PNP switch status/
ON or OFF
Shift lever is:
On D: ON
Not on D: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

Continuously shift to "+" (up-shift): ON

·

Release "+" (up-shift): OFF


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

Continuously shift to "+" (down-shift): ON

·

Release "+" (down-shift): OFF


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
Shift lever position is:
On S, "+" and "-": ON
Not on S, "+" and "-": OFF
-


PROCEDURE

1.CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - BATTERY)
a.

Disconnect the D4 park/neutral position switch connector.


U189435E02
1.813,1.104 2.01,0.594 false 0.073,0.073 1.5,0.271 1.427,0.198 10 false Wire Harness Side: 1.979,0.385 2.188,0.563 0.208,0.177 10 false RB 0.354,1.125 0.729,1.354 0.375,0.229 10 false D4

b.

Turn the ignition switch on (IG).


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
D4-2 (RB) - Body ground 10 to 14 V




OK

2.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

CHECK POWER SOURCE OF ECM

2.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C140841E03
2.313,1.792 2.125,1.323 false 1.958,1.792 1.781,1.323 false 1.552,0.875 1.375,0.406 false 1.063,1.802 1.24,1.333 false 1.948,0.885 2.135,0.417 false 1.271,0.229 1.552,0.438 0.281,0.208 10 false RB 2.063,0.24 2.344,0.448 0.281,0.208 10 false RL 1.917,1.813 2.198,2.021 0.281,0.208 10 false DL 0.958,1.823 1.24,2.031 0.281,0.208 10 false NL 2.271,1.813 2.5,2.021 0.229,0.208 10 false PL

Disconnect the D4 park/neutral position switch connector.


b.

Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.

Standard resistance:
Tester Connection Shift Lever Position Specified Condition
6 (PL) - 2 (RB) P Below 1 Ω
6 (PL) - 2 (RB) Not on P 10 kΩ or higher
1 (RL) - 2 (RB) R Below 1 Ω
1 (RL) - 2 (RB) Not on R 10 kΩ or higher
9 (NL) - 2 (RB) N Below 1 Ω
9 (NL) - 2 (RB) Not on N 10 kΩ or higher
7 (DL) - 2 (RB) D, S, "+" and "-" Below 1 Ω
7 (DL) - 2 (RB) Not on D, S, "+" and "-" 10 kΩ or higher




OK

3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C115837E07
1.115,1.844 1.333,1.292 false 1.333,0.896 1.115,0.344 false 1.052,1.865 1.24,2.063 0.188,0.198 10 false S 1.031,0.177 1.302,0.375 0.271,0.198 10 false IG

Disconnect the G9 transmission control switch connector of the shift lock control unit.


b.

Measure the resistance between each terminal of the shift lock control unit when the shift lever is moved to each position.

Standard resistance:
Tester Connection Shift Lever Position Specified Condition
6 (IG) - 13 (S) S, "+" and "-" Below 1 Ω
6 (IG) - 13 (S) Not on S, "+" and "-" 10 kΩ or higher




OK

4.CHECK WIRE HARNESS (ECM - BATTERY)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

4.CHECK WIRE HARNESS (ECM - BATTERY)
a.

Disconnect the D2 ECM connector.


b.

Turn the ignition switch on (IG).


U189333E02
0.958,1.729 0.563,1.104 false 1.313,1.75 1.708,1.125 false 1.042,1.729 0.927,1.104 false 1.135,1.729 1.26,1.104 false 1.51,2.583 1.385,1.958 false 1.177,2.583 1.302,1.958 false 2.333,0.844 2.708,1.073 0.375,0.229 10 false D2 1.125,2.604 1.302,2.802 0.177,0.198 10 false P 1.219,0.875 1.396,1.073 0.177,0.198 10 false N 1.677,0.875 1.885,1.073 0.208,0.198 10 false D 0.875,0.875 1.063,1.073 0.188,0.198 10 false R 0.073,0.063 1.427,0.229 1.354,0.167 10 false Wire Harness Side: 0.313,0.875 0.76,1.073 0.448,0.198 10 false STAR 1.479,2.594 1.656,2.792 0.177,0.198 10 false S

c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Shift Lever Position Specified Condition
D2-52 (STAR) - Body ground P or N Below 2 V
D2-52 (STAR) - Body ground Not on P or N 10 to 14 V
D2-73 (P) - Body ground P 10 to 14 V
D2-73 (P) - Body ground Not on P Below 1 V
D2-53 (R) - Body ground R 10 to 14 V*
D2-53 (R) - Body ground Not on R Below 1 V
D2-54 (N) - Body ground N 10 to 14 V
D2-54 (N) - Body ground Not on N Below 1 V
D2-56 (D) - Body ground D and S 10 to 14 V
D2-56 (D) - Body ground Not on D and S Below 1 V
D2-74 (S) - Body ground S, "+" and "-" 10 to 14 V
D2-74 (S) - Body ground Not on S, "+" and "-" Below 1 V


HINT:

*: The voltage will drop slightly due to the illumination of the back-up light.




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR