The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0705 | When one of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic) ·
P input signal is ON ·
N input signal is ON ·
R input signal is ON ·
D input signal is ON (B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic) ·
STAR input signal is ON ·
R input signal is ON ·
D input signal is ON (C) When any of following conditions is for 2 sec. or more in the S position (2 trip detection logic) ·
STAR input signal is ON ·
P input signal is ON ·
N input signal is ON ·
R input signal is ON (D) All of the following signals are OFF simultaneously (2 trip detection logic)* ·
STAR input signal is OFF ·
P input signal is OFF ·
N input signal is OFF ·
R input signal is OFF ·
D input signal is OFF |
·
Open or short in park/neutral position switch circuit ·
Park/Neutral position switch ·
ECM |
*: Only for Euro-OBD vehicle
These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is on P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N or D).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Follow the instructions on the tester and read the Data List.
| Item | Measurement Item/
Range (Display) |
Normal Condition | Diagnostic Note |
|---|---|---|---|
| Neutral Position Switch Signal | PNP switch status/
ON or OFF |
Shift lever is:
On P or N: ON Not on P or N: OFF |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Stop Light Switch | Stop light switch status/
ON or OFF |
·
Brake pedal is depressed: ON ·
Brake pedal is released: OFF |
- |
| Shift status | ECM gear shift command/
1st, 2nd, 3rd or 4th |
Shift lever position is:
On D: 1st, 2nd, 3rd or 4th |
- |
| Shift switch status (R range) | PNP switch status/
ON or OFF |
Shift lever is:
On R: ON Not on R: OFF |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (P range) | PNP switch status/
ON or OFF |
Shift lever is:
On P: ON Not on P: OFF |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (N range) | PNP switch status/
ON or OFF |
Shift lever is:
On N: ON Not on N: OFF |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (D range) | PNP switch status/
ON or OFF |
Shift lever is:
On D: ON Not on D: OFF |
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Sports Shift Up SW | Sport shift up switch status/
ON or OFF |
·
Continuously shift to "+" (up-shift): ON ·
Release "+" (up-shift): OFF |
- |
| Sports Shift Down SW | Sport shift down switch status/
ON or OFF |
·
Continuously shift to "+" (down-shift): ON ·
Release "+" (down-shift): OFF |
- |
| Sports Mode Selection SW | Sport mode select switch status/
ON or OFF |
Shift lever position is:
On S, "+" and "-": ON Not on S, "+" and "-": OFF |
- |
Disconnect the D4 park/neutral position switch connector.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| D4-2 (RB) - Body ground | 10 to 14 V |
OK
NG
Disconnect the D4 park/neutral position switch connector.
Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
|---|---|---|
| 6 (PL) - 2 (RB) | P | Below 1 Ω |
| 6 (PL) - 2 (RB) | Not on P | 10 kΩ or higher |
| 1 (RL) - 2 (RB) | R | Below 1 Ω |
| 1 (RL) - 2 (RB) | Not on R | 10 kΩ or higher |
| 9 (NL) - 2 (RB) | N | Below 1 Ω |
| 9 (NL) - 2 (RB) | Not on N | 10 kΩ or higher |
| 7 (DL) - 2 (RB) | D, S, "+" and "-" | Below 1 Ω |
| 7 (DL) - 2 (RB) | Not on D, S, "+" and "-" | 10 kΩ or higher |
OK
NG
(See pageDrivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>COMPONENTS)
Disconnect the G9 transmission control switch connector of the shift lock control unit.
Measure the resistance between each terminal of the shift lock control unit when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
|---|---|---|
| 6 (IG) - 13 (S) | S, "+" and "-" | Below 1 Ω |
| 6 (IG) - 13 (S) | Not on S, "+" and "-" | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the D2 ECM connector.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Shift Lever Position | Specified Condition |
|---|---|---|
| D2-52 (STAR) - Body ground | P or N | Below 2 V |
| D2-52 (STAR) - Body ground | Not on P or N | 10 to 14 V |
| D2-73 (P) - Body ground | P | 10 to 14 V |
| D2-73 (P) - Body ground | Not on P | Below 1 V |
| D2-53 (R) - Body ground | R | 10 to 14 V* |
| D2-53 (R) - Body ground | Not on R | Below 1 V |
| D2-54 (N) - Body ground | N | 10 to 14 V |
| D2-54 (N) - Body ground | Not on N | Below 1 V |
| D2-56 (D) - Body ground | D and S | 10 to 14 V |
| D2-56 (D) - Body ground | Not on D and S | Below 1 V |
| D2-74 (S) - Body ground | S, "+" and "-" | 10 to 14 V |
| D2-74 (S) - Body ground | Not on S, "+" and "-" | Below 1 V |
*: The voltage will drop slightly due to the illumination of the back-up light.
OK
NG