Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0982  Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4)  P0983  Shift Solenoid "D" Control Circuit High (Shift Solenoid Valve S4)  


DESCRIPTION

Shifting from 1st to O/D is performed in combination with the ON and OFF operation of the shift solenoid valves SL1 and SL2, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

DTC No. DTC Detection Condition Trouble Area
P0982 ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1 trip detection logic)
·

Short in shift solenoid valve S4 circuit

·

Shift solenoid valve S4

·

ECM


P0983 ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1 trip detection logic)
·

Open in shift solenoid valve S4 circuit

·

Shift solenoid valve S4

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve S4 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Also, the ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the circuit (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

WIRING DIAGRAM

C142136E02
6.041,2.775 6.438,2.956 0.397,0.182 10 ECM 5.86,1.682 6.256,1.863 0.397,0.182 10 S4 5.537,1.457 5.933,1.639 0.397,0.182 10 78 2.686,1.787 3.082,1.968 0.397,0.182 10 8 2.362,1.787 2.640,1.968 0.279,0.182 10 S4 0.789,2.769 2.417,3.092 1.628,0.323 10 Shift Solenoid Valve S4 (ECT Solenoid) 5.537,1.682 5.933,1.863 0.397,0.182 10 D2 0.789,2.588 2.417,2.760 1.628,0.172 10 D51

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S4)
C141259E11
1.865,1.76 1.708,1.25 true 1.802,1.771 2.083,1.969 0.281,0.198 10 false S4

a.

Disconnect the D51 wire connector.


b.

Measure the resistance of the transmission wire.

Standard resistance:
Tester Connection Condition Specified Condition
8 (S4) - Body ground 20°C (68°F) 11 to 15 Ω




OK

2.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE S4
2.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)
U189339E02
1.74,1.969 1.958,2.635 true 1.542,0.938 1.917,1.167 0.375,0.229 10 false D2 1.896,2.667 2.146,2.865 0.25,0.198 10 false S4 0.135,0.094 1.521,0.26 1.385,0.167 10 false Wire Harness Side:

a.

Disconnect the D2 ECM connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
D2-78 (S4) - Body ground 20°C (68°F) 11 to 15 Ω




OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE S4
C366241E01
0.885,2.333 1.198,2.573 0.313,0.24 10 false (-) 1.604,2.333 1.917,2.573 0.313,0.24 10 false (+)

a.

Remove the shift solenoid valve S4.


b.

Measure the resistance of the solenoid valve.

Standard resistance:

11 to 15 Ω at 20°C (68°F)



c.

Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes operating noise.




OK

REPAIR OR REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE S4