Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Shifting from 1st to O/D is performed in combination with the ON and OFF operation of the shift solenoid valves SL1 and SL2, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

DTC No. DTC Detection Condition Trouble Area
P0778 Duty cycle to shift solenoid valve SL2 is 100% (1 trip detection logic)
·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Also, the ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the circuit (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).

WIRING DIAGRAM

C142133E11
6.031,2.74 6.427,2.927 0.396,0.188 10 false ECM 5.51,2.219 5.906,2.406 0.396,0.188 10 false D2 5.51,1.292 5.906,1.479 0.396,0.188 10 false D2 5.844,1.281 6.281,1.469 0.438,0.188 10 false SL2+ 5.854,2.219 6.333,2.406 0.479,0.188 10 false SL2- 5.51,1.073 5.948,1.26 0.438,0.188 10 false 58 5.521,2.01 6,2.198 0.479,0.188 10 false 59 2.177,1.406 2.573,1.594 0.396,0.188 10 false SL2+ 2.188,2.333 2.51,2.521 0.323,0.188 10 false SL2- 2.646,1.406 3.042,1.594 0.396,0.188 10 false 4 2.646,2.323 2.969,2.51 0.323,0.188 10 false 9 0.823,2.938 2.615,3.323 1.792,0.385 10 false Shift Solenoid Valve SL2 (ECT Solenoid Valve) 0.833,2.74 1.229,2.896 0.396,0.156 10 false D51

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)
a.
C141259E07
1.469,0.969 1.313,0.563 false 1.302,1.677 1.458,1.271 false 1.167,0.385 1.573,0.583 0.406,0.198 10 false SL2+ 1.167,1.698 1.573,1.896 0.406,0.198 10 false SL2-

Disconnect the D51 wire connector.


b.

Measure the resistance of the transmission wire.

Standard resistance:
Tester Connection Condition Specified Condition
4 (SL2+) - 9 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
4 (SL2+) - Body ground 20°C (68°F) 1 MΩ or higher
9 (SL2-) - Body ground 20°C (68°F) 1 MΩ or higher




OK

2.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL2
2.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)
a.
U189338E02
1.479,1.75 1.26,1.094 true 1.563,1.75 1.781,1.094 true 0.438,0.781 0.813,1.01 0.375,0.229 10 false D2 1.667,0.927 2.073,1.125 0.406,0.198 10 false SL2- 1.083,0.927 1.49,1.125 0.406,0.198 10 false SL2+ 0.146,0.135 1.51,0.302 1.365,0.167 10 false Wire Harness Side:

Disconnect the D2 ECM connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
D2-58 (SL2+) - D2-59 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
D2-58 (SL2+) - Body ground 20°C (68°F) 1 MΩ or higher
D2-59 (SL2-) - Body ground 20°C (68°F) 1 MΩ or higher




OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL2
a.

Remove the shift solenoid valve SL2.


C140848E08
1.021,0.479 1.479,0.938 false 2.24,0.49 1.781,0.948 false 1.031,2.604 1.49,3.073 false 2.24,2.594 1.781,3.063 false 0.906,0.375 1.198,0.583 0.292,0.208 10 false 1 2.281,0.365 2.5,0.563 0.219,0.198 10 false 2 0.917,2.5 1.208,2.708 0.292,0.208 10 false 1 2.281,2.479 2.5,2.677 0.219,0.198 10 false 2 1.208,4.104 1.604,4.354 0.396,0.25 10 false (-) 1.917,4.104 2.281,4.313 0.365,0.208 10 false (+)

b.

Measure the resistance of the solenoid valve.

Standard resistance:

5.0 to 5.6 Ω at 20°C (68°F)



c.

Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes operating noise.




OK

REPAIR OR REPLACE TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE SL2