Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM D

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  ROAD TEST  


PROBLEM SYMPTOM CONFIRMATION


a.

Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that the transaxle does not shift up, shift down, or the shift point is too high or too low, conduct the following road test while referring to the automatic shift schedule and simulate the problem symptoms.



ROAD TEST


NOTICE:

Perform the test at the normal operating ATF temperature of 50 to 80°C (122 to 176°F).


a.

D position test

Move the shift lever to D and fully depress the accelerator pedal. Check the following:

i.

Check up-shift operation.

Check that the 1 → 2, 2 → 3 and 3 → O/D up-shifts take place at the shift point shown in the automatic shift schedule (see page General>SPECIFICATIONS>U241E AUTOMATIC TRANSMISSION / TRANSAXLE>SERVICE DATA).

HINT:

O/D Gear Up-shift Prohibition Control

·

Engine coolant temperature is 55°C (131°F) or less and vehicle speed is at 70 km/h (43 mph) or less.


·

ATF temperature is 5°C (41°F) or less.


O/D Gear Lock-up Prohibition Control

·

Brake pedal is depressed.

·

Accelerator pedal is released.

·

Engine coolant temperature is 60°C (140°F) or less.




ii.

Check for shift shock and slip.

Check for shock and slip at the 1 → 2, 2 → 3 and 3 → O/D up-shifts.


iii.

Check for abnormal noise and vibration.

Check for abnormal noise and vibration when up-shifting from 1 → 2, 2 → 3 and 3 → O/D while driving with the shift lever on D, and check while driving in the lock-up condition.

HINT:

The check for the cause of abnormal noise and vibration must be done thoroughly as it could also be due to loss of balance in the differential, torque converter assembly, etc.



iv.

Check kick-down operation.

While driving the vehicle in the 2nd, 3rd and O/D gears with the shift lever on D, check that the possible kick-down vehicle speed limits for 2 → 1, 3 → 2 and O/D → 3 kick-downs conform to those indicated in the automatic shift schedule (see page General>SPECIFICATIONS>U241E AUTOMATIC TRANSMISSION / TRANSAXLE>SERVICE DATA).


v.

Check for abnormal shock and slip at kick-down.


vi.

Check the lock-up mechanism.

·

Drive the vehicle in the O/D gear with the shift lever on D. Maintain a steady speed (lock-up ON).

·

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.


HINT:
·

There is no lock-up function in the 1st and 2nd gear.

·

If there is a sudden increase in engine speed, there is no lock-up.





b.

S position test

Shift to the S position, depress the accelerator pedal and check the following points:

i.

Check shift operation.

·

While driving in the D position and O/D gear, shift into the S position and back to the D position. Check that the gear changes O/D → 3 down-shift and 3 → O/D up-shift can be performed.

·

With the shift lever in the S position (with the vehicle stopped), shift into the "+" position to check that the shift position on the combination meter changes as follows: 1 → 2, 2 → 3 and 3 → O/D.

·

While driving in the 3(S) position and 3rd gear (at a vehicle speed of about 30 to 40 km/h (19 to 25 mph)), shift into the "-" position and check if the 2nd gear down-shift occurs and if the engine brake performs properly.

·

While driving in the 2(S) position and 2nd gear (at a vehicle speed of about 20 to 30 km/h (12 to 19 mph)), shift into the "-" position and check if the 1st gear down-shift occurs and if the engine brake performs properly.


HINT:

Manual shift (S position) prohibition control.

·

Down-shifting causes engine overrun.

·

Down-shifting is required continuously. (Down-shifting to 1st gear can not be performed.)





c.

R position test

Move the shift lever to R and lightly depress the accelerator pedal. Check that the vehicle moves backward without any abnormal noise or vibration.

CAUTION:

Before conducting this test, ensure that no people or obstacles are in the test area.



d.

P position test

Stop the vehicle on an incline (more than 5°). Then move the shift lever to P and release the parking brake. Check that the parking lock pawl holds the vehicle in place.


e.

Uphill/downhill control function test

i.

Check that the gear does not up-shift to the O/D gear while the vehicle is driving uphill.


ii.

Check that the gear automatically down-shifts from the O/D to 3rd gear when the brake pedal is depressed while the vehicle is driving downhill.